Bedienungsanleitung Black Decker CS355 T1 (Seite 7 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

579640

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

(Original instructions)

u Replace the cutting disc (J). Make sure that the new disc

is placed onto the spacer (R) in the correct rotational

direction.

u Secure the blade with the retaining ange (U), the washer

(T) and the bolt (S).

u Push in the spindle lock (L).

u Rotate the cutting disc (J) until it locks.

u Using the at wrench (G), tighten the bolt (S) by turning

clockwise.

u Move the guard back down and release the spindle lock

(L).

u Adjust the cutting depth as necessary.

Adjusting the cutting depth (g. 1)

The cutting depth can be adjusted to meet the wear of the

cutting disc.

u Make a dry run with the tool switched off and check for

clearance.

u If adjustment is required, proceed as follows:

u Loosen the lock nut (M) a few turns.

u Turn the depth stop bolt (M) in or out as to achieve the

required cutting depth.

u Tighten the lock nut (M).

Warning: Always adjust the depth stop to its original position

when replacing the cutting disc.

Clamping the workpiece in position (g. 2 - g 4)

The tool is equipped with a vise (F)

u Pull the lever (I) toward the handle (H).

u Push the vise (F) forward until the jaw is almost touching

the workpiece.

u Press the lever (I) toward the jaw until it engages with the

clamp shaft.

u Rotate the handle (H) clockwise and clamp the workpiece

securely.

u To release the workpiece, rotate the handle (H)

counterclockwise.

u To increase the cutting capacity, place a spacer block

under the workpiece. The spacer block should be slightly

narrower than the workpiece.

Warning: Support long workpieces using a piece of wood. Do

not clamp the cut off end.

Quick travel feature (g. 4)

The clamp has a quick travel feature.

u To release the clamp, rotate the handle (H) one or two

turns counterclockwise and pull the lever (I) toward the

handle (H).

Setting the clamping position (g. 5)

The clamping position can be set to match the cutting disc.

u Remove the fence bolts (P) using the at wrench (G).

u Move the fence (E) as required.

u Re-t the fence bolts (P) and tighten them to lock the

fence (E).

Adjusting the angle of cut (g. 6)

The tool can be used for mitre cuts up to 45°.

u Loosen the fence bolts (P) to release the fence (E).

u Set the fence (E) to the required angle. The angle can be

read on the scale (Q).

u Tighten the fence bolts (P) to lock the fence (E).

Checking and adjusting the mitre scale (g. 6)

u Loosen the fence bolts (P) to release the fence (E).

u Pull down the arm and lock it in this position by attaching

the lock chain (A).

u Place a square against the fence (E) and the left side of

the cutting disc creating a perfect 90°. Check that the 0°

marking on the scale (Q) aligns with the marking on the

base (D).

u Tighten the fence bolts (P) to lock the fence (E).

u Remove the lock chain (A) and return the arm to its upper

rest position.

Adjusting the spark deector (g. 1)

u Loosen the screw (B).

u Set the spark deector (C) as appropriate.

u Tighten the screw (B).

Use

Warning: Always observe the safety instructions and

applicable regulations.

Warning: Do not apply excessive pressure to the tool.

Warning: Avoid overloading. Should the tool become hot, let

it run a few minutes under no load condition.

Cutting capacity

The wide vise opening and high pivot point provide cutting

capacity for many large pieces. Use the cutting

capacity chart to determine total maximum size of cuts that

can be made with a new wheel.

Caution: Certain large, circular or irregularly shaped objects

may require additional holding means if they cannot be held

securely in vise.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker CS355 T1 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker CS355 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info