Bedienungsanleitung Black Decker GKC 1000 (Seite 13 von 128) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

78140

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

ENGLISH

Checking and adjusting the saw chain tension (fig. C)

To tension the saw chain (14) slacken the two chain cover

retention bolts (12) with the spanner (13) and the chain

tensioning device will push the chain guide bar (3) out,

setting the correct tension. Retighten the two retention bolts

(12) securely.

Check the correct tension has been set by lightly pulling on

the saw chain (14). The tension is correct when the saw

chain snaps back after being pulled 3 mm away from the

guide bar. There should be no "sag" between the chain guide

bar (3) and the saw chain (14) on the underside.

Note: Do not over tension the saw chain as this will lead to

excessive wear and reduce the life of the bar and saw chain.

It will also lead to reduced product performance.

Note: With first use and when the saw chain is new, check

tension frequently as a new saw chain stretches slightly.

Replacing the saw chain and chain guide bar

After prolonged use the saw chain (14) and /or chain guide

bar (3) may need replacing. Ensure only Black & Decker

recommended replacements are used.

Removing the saw chain and chain guide bar (fig. C & D)

Always wear protective gloves when installing or

removing the saw chain (14). The saw chain is

sharp and can cut you when it is not running.

Warning! The chain guide bar and the saw chain may be hot

after use. Allow to cool before replacing.

 Place the tool on a firm surface.

 Rotate the two retention bolts (12) counter clockwise

with the spanner (13) provided and remove completely.

 Remove the chain access cover (11).

 Slide the latch (5) to the unlock position, open the

handles and pull back the top jaw (1).

 Pull back chain guide bar (3) and then lift the saw chain

(14) out of the groove in the guide bar. The saw chain

can then be removed from the unit.

 The chain guide bar (3) can then be angled up and

removed.

Assembling the chain guide bar and saw chain

(fig. E & F)

Warning! Always wear protective gloves when installing or

removing the saw chain. The saw chain is sharp and can cut

you when it is not running.

 Ensure the operation is carried out on a firm surface.

 Slide the latch (5) to the unlock position, open the

handles and pull back the top jaw (1).

 Insert the chain guide bar (3) into the space between the

chain tensioner and align with the chain guide bar

locator, angle the chain guide bar (3) down ensuring it is

correctly located.

 Place the saw chain (14) around the front of the chain

guide bar (3).

 Pull the chain guide bar (3) and the saw chain (14)

back, engaging it in the groove in the chain guide bar (3)

and then over the sprocket (16) positioning teeth in the

correct position on the sprocket.

 Replace the chain access cover (11) and the two

retention bolts (12) tightening securely.

 Ensure the saw chain (14) is fitted correctly with

reference to the markings on the tool.

Oiling (fig. G)

 Before first use and every ten minutes of use you must

oil the product with the correct chain oil. (Cat No A6027)

Open the oiling cover (4) and insert the bottle into the oil

filling hole (15), apply pressure to the bottle once to

dispense oil.

 This should be adequate for about 10 minutes of cutting

depending upon cutting speed and type of wood.

The hole feeds the oil through to the saw chain on to the chain

guide bar (3) and an excessive amount of oil applied to the unit

could mean the oil drips from the unit around the jaw area. This

is normal and is nothing to be concerned about.

Use

Charging the battery (fig. H)

The battery (6) needs to be charged before first use and

whenever it fails to produce sufficient power on jobs that

were easily done before. When charging the battery (6) for

the first time, or after prolonged storage, it will only accept an

80% charge.

After several charge and discharge cycles, the battery (6)

will attain full capacity. The battery (6) may become warm

while charging; this is normal and does not indicate a

problem.

Warning! Do not charge the battery at ambient temperatures

below 10°C or above 40°C. Recommended charging

temperature is approximately 24°C.

Charger (fig. H)

 To charge the battery (6), remove it from the tool and

slide the charger receptacle (10) onto the battery (6).

 Plug in the charger (9).

The battery (6) will be fully charged in approximately eight

hours. It can be removed at any time or left in the connected

charger indefinitely.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GKC 1000 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info