Bedienungsanleitung Black Decker GL337SB (Seite 8 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

527582

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

Fitting a new spool of cutting line (fig. H - J)

Spool with single cutting line (fig. H)

Replacement spools of cutting line are available from your

Black & Decker dealer (cat. no. A6481).

◆ Keep the tabs (16) depressed and remove the spool cover

(17) from the housing (12).

◆ Remove the empty spool (18) from the spool housing.

◆ Remove any dirt and grass from the spool cover and

housing.

◆ Take the new spool and unwind approximately 9 cm of

cutting line.

◆ Feed the cutting line through the eyelet (19).

◆ Push the spool onto the drive shaft (20) and rotate it

slightly until it is seated. Make sure that the cutting line

is not trapped under the spool and that 9 cm of cutting

line protrudes from the housing.

◆ Align the tabs on the spool cover with the holes in the

housing.

◆ Push the cover onto the housing until it snaps securely

into place.

Warning! If the cutting line protrudes beyond the trimming

blade (10), cut it off so that they just reach the blade.

Spool with twin cutting line (fig. I & J)

Replacement spools of cutting line are available from your

Black & Decker dealer (cat. no. A6441). Complete cassettes

containing a spool of cutting line are also available (cat. no. A6488).

◆ Keep the tabs (21) depressed and remove the spool cover

(22) from the housing (12).

◆ Remove the empty spool (23) from the spool cover.

◆ Remove any dirt and grass from the spool cover and

housing.

◆ Take the new spool and push it onto the boss in the spool

cover. Rotate the spool slightly until it is seated.

◆ Unclip the end of one of the cutting lines and feed the line

into one of the eyelets (24). The line should protrude

approximately 9 cm from the spool cover.

◆ Unclip the end of the other cutting line and feed the line

into the other eyelet. The line should protrude

approximately 9 cm from the spool cover.

◆ Align the tabs (21) on the spool cover with the cut-outs

(25) in the housing.

◆ Push the cover onto the housing until it snaps securely

into place.

Warning! If the cutting lines protrude beyond the trimming

blade (10), cut them off so that they just reach the blade.

Winding a new cutting line onto an empty spool (fig. K - O)

You may wind new cutting line onto an empty spool.

Spool with single cutting line (fig. K & L)

Replacement packs of cutting line are available from your

Black & Decker dealer (cat. no. A6170 (25 m) & A6171 (40 m)).

◆ Remove the empty spool from the tool as described

above.

◆ Remove any remaining cutting line from the spool.

◆ Feed 2 cm of cutting line into one of the holes (26) in the

spool as shown.

◆ Bend the cutting line and anchor it in the L-shaped slot (27).

◆ Wind the cutting line onto the spool in the direction of the

arrow (28). Make sure to wind the line on neatly and in

layers. Do not criss-cross.

◆ When the wound cutting line reaches the recesses (29),

cut the line. Let the line protrude approximately 9 cm from

the spool and hold a finger on the line to keep it in place.

◆ Proceed as described above to fit the spool on the tool.

Warning! Only use the appropriate type of Black & Decker

cutting line.

Spool with twin cutting line (fig. M - O)

Replacement packs of cutting line are available from your

Black & Decker dealer (cat. no. A6440).

◆ Remove the empty spool from the tool as described

above.

◆ Remove any remaining cutting line from the spool.

◆ First wind new line onto the uppermost part of the spool:

– Feed 2 cm of cutting line into one of the slots (30) in the

upper section of the spool as shown.

– Wind the cutting line onto the spool in the direction of

the arrow (31). Make sure to wind the line on neatly

and in layers. Do not criss-cross.

– When the wound cutting line reaches the recesses (32),

cut the line.

– Temporarily park the line in the slots (33) on one side of

the spool as shown.

◆ Repeat the above procedure for the second cutting line on

the lower section of the spool. Park the line in the unused

slots (33).

◆ Proceed as described above to fit the spool on the tool.

Do not forget to release the cutting line from the parking

slots (33).

Warning! Only use the appropriate type of Black & Decker

cutting line. Ensure that cutting line is present in both sections

of the spool.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GL337SB Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info