Bedienungsanleitung Black Decker GL4525 (Seite 8 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

527589

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

(Original instructions)

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

u Electric safety can be further improved by using a

highsensitivity 30 mA Residual Current Device (RCD).

Features

This appliance includes some or all of the following features.

1. On/off switch

2. Handle

3. Cable restraint

4. Power inlet

5. Second handle

6. Guard

7. Spool housing

8. Head

9. Edge guide

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting the guard (g. A-B)

u Remove the screw from the guard.

u Keeping the guard (6) square to the strimmer head (8)

slide it into place until the retaining tab clicks into place

(Ensure that the guide rails (10) on the guard (6) are

correctly aligned with the guide rails (11) on the strimmer

head (8). g. A).

u Secure the guard (6) with the screw (12).

Warning! Never use the tool unless the guard is properly

tted.

Attaching the second handle (g. C) (GL4525 &

GL5028 only)

u Slide the second handle (5) on to the main handle (2) in

an upwards direction.

u Secure the second handle in place with the screw (13)

provided.

Attaching the second handle (g. D) (GL5530 only)

u Press in and hold both of the buttons (14) on the side of

the handle.

u Slide the second handle (5) in place over the buttons (14).

Warning! Ensure that the teeth on the button are correctly

aligned in slots in the handle and that the handle is secure.

Adjusting the position of the secondary handle (g.

E) (GL5530 only)

The second handle (5) can be adjusted to provide optimum

balance and comfort.

u Press in the button (15) on the left side od the handle.

u Rotate the second handle (5) into the required position.

u Release the button (15).

Warning! Ensure that the teeth on the button are correctly

aligned in slots in the handle and that the handle is secure.

Adjusting the height of the tool (g. F)

This tool has a telescopic mechanism, allowing you to set it to

a comfortable height. There are multiple height settings.

To adjust the height setting, proceed as follows:

u Disconnect the tool from the supply.

u Loosen the adjustment collar (16) by turning it clockwise.

u Gently pull the tube (17) in or out of the handle (2) to the

desired height.

u Tighten the adjustment collar (16) by turning anti-

clockwise.

Releasing the cutting line

In transit, the cutting line is taped to the spool housing.

u Remove the tape holding the cutting line to the spool

housing (7).

Connecting the tool to the mains (g. G)

u Connect the female plug of a suitable extension cable to

the power inlet (4).

u Loop the cable through the cable restraint (3).

u Insert the mains plug into a mains outlet.

For wired in cable units: Make sure the cable is looped

through the cable restraint prior to connecting the plug to the

mains outlet.

Warning! The extension cable must be suitable for outdoor

use.

Use

Warning! Let the tool work at its own pace. Do not overload.

Setting the tool to trimming or edging mode (g. H,

I & J)

The tool can be used in trimming mode as shown in g. E or in

edging mode to trim overhanging grass along lawn edges and

ower beds as shown in g. F.

Trimming mode (g. H)

For trimming, the trimmer head should be in the position

shown in g. H. If it is not:

u Disconnect the tool from the supply.

u Loosen the adjustment collar (6) by turning it clockwise.

u Whilst holding the handle (2), rotate the head (8)

clockwise.

u Tighten the collar (6) by turning it anti-clockwise.

u Slide the edge guide (9) into the motor housing.

Note: Note: The head will only rotate in one direction.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GL4525 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info