Bedienungsanleitung Black Decker GL4525 (Seite 9 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

527589

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

(Original instructions)

Edging mode (g. I & J)

For edging, the trimmer head should be in the position shown

in g. I. If it is not:

u Disconnect the tool from the supply.

u Loosen the adjustment collar (6) by turning it clockwise.

u Whilst holding the handle (2), rotate the head (8)

anti-clockwise.

u Tighten the collar (6) by turning it anti-clockwise.

u Slide the edge guide out of the motor housing. Ensure that

the edging guide (9) is fully extended, an audible click will

be heard.

Note: The head will only rotate in one direction.

Switching on and off

u To switch the tool on, squeeze the trigger lever (1).

u To switch the tool off, release the trigger lever.

Warning! Never attempt to lock the trigger lever in the on

position.

Hints for optimum use

General

u In order to achieve optimum cutting results, only cut dry

grass.

Trimming

u Hold the tool as shown in g. K.

u Gently swing the trimmer from side to side.

u When cutting long grass, work in stages from the top. Take

small cuts.

u Keep the tool away from hard objects and delicate plants.

u Cutting line will wear faster and require more feeding if the

cutting is done along pavements or other abrasive

surfaces or heavier weeds are being cut.

u If the tool starts running slowly, reduce the load.

Edging

Optimum cutting results are achieved on edges deeper than

50 mm.

u Do not use the tool to create edges. To create edges,

use an edging spade.

u Guide the tool as shown in g. L.

u To make a closer cut, slightly tilt the tool.

Fitting a new spool of cutting line (g. M) (GL4525

& GL5028 only)

Replacement spools of cutting line are available from your

Black & Decker dealer (cat. no. A6481).

u Unplug the tool.

u Keep the tabs (18) depressed and remove the spool cover

(19) from the housing (7).

u Remove the empty spool (20) from the housing.

u Remove any dirt and grass from the spool cover and

housing.

u Take the new spool and push it onto the boss in the

housing. Rotate the spool slightly until it is seated.

u Unclip the end of one of the cutting lines and guide the

line into the eyelets(21). The line should protrude approx.

11 cm from the spool cover.

u Align the tabs (18) on the spool cover with the cut outs

(22) in the housing.

u Push the cover onto the housing until it snaps securely

into place.

Warning! If the cutting lines protrude beyond the trimming

blade (23), cut them off so that they just reach the blade.

Fitting a new spool of cutting line (g. N & O)

(GL5530 only)

Replacement spools of cutting line are available from your

Black & Decker dealer (cat. no. A6441). Complete cassettes

containing a spool of cutting line are also available (cat. no.

A6442).

u Unplug the tool.

u Keep the tabs (24) depressed and remove the spool cover

(25) from the housing (11) (g. N).

u Remove the empty spool (26) from the spool cover.

u Remove any dirt and grass from the spool cover and

housing.

u Take the new spool and push it onto the boss in the spool

cover. Rotate the spool slightly until it is seated.

u Unclip the end of one of the cutting lines and guide the

line into one of the eyelets (27) (g. O). The line should

protrude approx. 11 cm from the spool cover.

u Unclip the end of the other cutting line and guide the line

into the other eyelet. The line should protrude approx. 11

cm from the spool cover.

u Align the tabs (24) on the spool cover with the cut outs

(28) in the housing (g. N).

u Push the cover onto the housing until it snaps securely

into place.

Warning! If the cutting lines protrude beyond the trimming

blade (10), cut them off so that they just reach the blade.

Winding new line onto an empty spool (g. P - R)

(GL5530 only)

You may wind new cutting line onto an empty spool.

Replacement packs of cutting line are available from your

Black & Decker dealer (cat. no. A6170 (31 m), A6171 (50 m)).

u Remove the empty spool from the tool as described

above.

u Remove any remaining cutting line from the spool.

u Feed 2 cm of cutting line into one of the holes (29) in the

spool as shown (g. P).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GL4525 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info