Bedienungsanleitung Black Decker GL670P (Seite 13 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

527606

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

◆ When there are no plants near the cutting

area, set the plant protector to position D.

MAINTENANCE

Your Black & Decker tool has been designed to

operate over a long period of time with a

minimum of maintenance. Continuous satisfactory

operation depends upon proper tool care and

regular cleaning.

Before performing any maintenance,

switch off and unplug the tool.

◆ Regularly clean the ventilation slots in your tool

using a soft brush or dry cloth.

◆ Regularly clean the cutting line and spool

using a soft brush or dry cloth.

◆ Regularly use a blunt scraper to remove grass

and dirt from the underneath of the guard.

Fitting a new spool of cutting line (fig. K & L)

Replacement spools of cutting line are available

from your Black & Decker dealer (cat. no. A6441).

Complete cassettes containing a spool of cutting

line are also available (cat. no. A6442).

◆ Unplug the tool.

◆ Keep the tabs (21) depressed and remove the

spool cover (22) from the housing (23) (fig. K).

◆ Remove the empty spool (24) from the

spool cover.

◆ Remove any dirt and grass from the spool

cover and housing.

◆ Take the new spool and push it onto the boss

in the spool cover. Rotate the spool slightly

until it is seated.

◆ Unclip the end of one of the cutting lines and

guide the line into one of the eyelets (25) (fig. L).

The line should protrude approx. 9 cm from the

spool cover.

◆ Unclip the end of the other cutting line and

guide the line into the other eyelet. The line

should protrude approx. 9 cm from the

spool cover.

◆ Align the tabs (21) on the spool cover with the

holes (26) in the housing (fig. K).

◆ Push the cover onto the housing until it snaps

securely into place.

If the cutting lines protrude beyond the

trimming blade (12), cut them off so that

they just reach the blade.

Winding new line onto an empty spool

(fig. M, N & P)

You may wind new cutting line onto an empty

spool. Replacement packs of cutting line are

available from your Black & Decker dealer

(cat. no. A6440).

◆ Remove the empty spool from the tool as

described above.

◆ Remove any remaining cutting line from

the spool.

◆ First wind new line onto the uppermost part of

the spool:

- Feed 2 cm of cutting line into one of the slots

in the upper section of the spool as shown.

- Wind the cutting line onto the spool in the

direction of the arrow. Make sure to wind the

line on neatly and in layers. Do not criss-cross.

- When the wound cutting line reaches the

recesses (28), cut the line.

- Temporarily park the line in the slots (27) on

one side of the spool as shown.

◆ Repeat the above procedure for the second

cutting line on the lower section of the spool.

Park the line in the unused slots (27).

◆ Proceed as described above to fit the spool on

the tool. Do not forget to release the cutting

line from the parking slots (27).

Only use the appropriate type of

Black & Decker cutting line. Ensure that

cutting line is present in both sections of

the spool (fig. P).

TROUBLESHOOTING

If your tool seems not to operate properly, follow

the instructions below. If this does not solve the

problem, please contact your local Black & Decker

repair agent.

Before proceeding, unplug the tool.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GL670P Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info