Bedienungsanleitung Black Decker GX302 (Seite 4 von 47) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Spanisch)

474472

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

Plug replacement

• Disconnect the plug from the supply.

• Cut off the plug and dispose of

immediately. Insertion of a detatched

plug into a 13 amp socket outlet may

result in electric shock.

• Only fit BS1363A approved plugs fitted

with the correctly rated fuse.

• The cable wire colours, or a letter, will be

marked at the connection points of most

good quality plugs. Attach the wires to

their respective points in the plug (see

below). Brown is for “Live” (L) and blue is

for “Neutral” (N).

• Before replacing the top cover of the

mains plug ensure that the cable restraint

is holding the outer sheath on the cable

firmly and that the two leads are correctly

fixed at the terminal screws.

Fit a

BS1363A

approved

plug

Connect blue

to N (neutral)

Make sure that the

outer sheath of the

cable is held firmly

by the clamp

Fit the

recommended

fuse

Connect brown

to L (live)

240 volts AC only.

Never use a light

socket

Warning! Never connect live or neutral wires

to the earth pin marked “E” or .

Note: Do not wire an extension cable directly

into your mower yourself. Instead, take your

mower to your nearest Black & Decker

service agent.

Increased safety can be obtained by having

a qualified electrician install a high sensitivity

(30mA) circuit breaker in the house wiring.

If you do not have such a circuit breaker

installed, or you do not wish to have one

installed, then we strongly recommend that

the electrical power to your mower be

supplied through a high sensitivity residual

current device (RCD). The RCD is designed

to provide a high degree of personal

protection against harmful electric current

should fault conditions occur.

Warning! The use of an RCD or other circuit

breaker unit does not release the operator of

your mower from the safety instructions and

safe working practices given in this manual.

Handle assembly (Fig. A - D)

Remove all the parts from the carton and

familiarise yourself with the individual parts of

your mower.

The main parts of your mower are your

mower body (1) which comprises the cutter

cover (2), motor cover (3), air vent shroud (5),

pivot blocks (6) and pivot pins (8).

The handle (10) comprises the lower handle

(11), the upper handle (12), switch box (13)

with switch lever (14) and safety lock-off

switch (15), electrical supply cable (16), the

cable clips (17), and the handle clamp

assemblies (18) which each comprise a wing

nut, washer and bolt.

Note: The electrical supply cable should be

positioned on the right-hand side of your

mower when viewed from the operating

position. Ensure that this is not damaged

or twisted before you begin to assemble

your mower.

Assemble the lower handle to your mower

body, as follows:

• Place the lower handle (11) into the pivot

blocks (6) on the cutter cover (2).

Note: It will be necessary to tilt the lower

handle towards the rear of your mower to

allow pivot pins (8) to fit correctly.

• Fit the pivot pins (8) through the holes in

the pivot block flanges (6) and through

the holes in the lugs on the lower

handle (11).

• Using a mallet, or similar tool, tap the

pivot pin (8) through the inner part of the

pivot block (6). The hooks on the end of

the pivot pin will click into position behind

the inner wall, retaining it in position.

• Repeat the process on the other side.

With the lower handle in position, assemble

the upper handle, as follows:

• Place the upper handle (12) over the

lower handle (11). Ensure the upper bend

is as shown in Fig. A.

• Align the holes in both the upper and

lower handles and fit a bolt (20) through

each hole. Fit a washer (21) to each bolt

and fit the wing nuts (22) on to the bolts.

Tighten each one with hand pressure only.

Note: Do not use a spanner or other

implement to tighten the wing nuts.

With the upper and lower handles

assembled, fit the switch box to the upper

handle, as follows:

Note: The switch box must be positioned on

the right-hand side of your mower.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GX302 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info