Bedienungsanleitung Black Decker GX302 (Seite 5 von 47) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Spanisch)

474472

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

Ensure that the electrical supply cable is

not twisted before you begin to assemble

the handle.

• Locate the two pins on the switch box (13)

with the holes in the upper handle (12).

• Fit the retaining plate (23) over the stem

of the handle (12) ans secure in position

using the two screws (24) provided.

Note: Do not overtighten these screws - light

pressure will be sufficient to hold the switch

box in position.

• Finally, secure the electrical supply cable

to the lower handle using the cable clip

(17) supplied.

Handle operation (Fig. E)

The handle has three positions, two storage

(park) positions and one operating position.

Positions 1 and 3 in Fig. E are the storage

(park) positions and F is the operating range.

For storage purposes, the handle assembly

can be set to position 2 or 3, as follows:

• With the handle in its working range F,

pivot the handle downwards until it

contacts the stops on the end of the

handle tube. This is the park position

2 for the handle.

• The handle can be moved to a park

position 3. Push the handle upwards in

the working range F, to the top position

1. Pull the handle upwards. While still

pulling the handle upwards, pivot the

handle down towards the ground to

position 3.

Height of cut adjustment (Fig. F & G)

Your mower employs a manual method of

height of cut adjustment. The method

involves changing the arrangement of the

spacers fitted between the impeller and the

blade, and applies to mowers fitted with the

steel or plastic blade cutting systems which

can be purchased as an accessory.

The following procedure assumes that the

steel blade is fitted. If the plastic blade

cutting system is fitted then take blade to

mean blade carrier. The blade carrier (25) is

shown in Fig. F.

The procedure for adjusting the height of cut

is as follows:

Caution: The plastic blade cutting system has

been designed to maintain lawns at a fixed

length, not for cutting long grass. We strongly

recommend that you use the steel blade to

cut your grass to the required length, then

use the plastic blade to maintain that length.

• Ensure your mower is disconnected from

the mains supply.

• Place the handle assembly into position

3 (see “Handle operation”).

• Turn your mower over onto its side so

that the underside of the cutter cover

is exposed.

• Using a cloth placed over the blades or

heavy duty gloves to protect your hands,

grip the blade and, using the spanner

provided, loosen and remove the nut

(21) from the motor spindle. Turn the nut

in anti-clockwise direction to loosen it.

Note: If the plastic blade cutting system is

fitted then it will be necessary to grip the

blade carrier (25) firmly to prevent it from

turning (Fig. F).

• Remove the blade nut, white washer

(26) (if supplied), spacers and blade

(21-24) and re-assemble to give the cut

height required, showing the 6 cut

heights available.

• Once the cut height is selected,

re-assemble the blade, ensuring the

cutter blade (23) is assembled with the

cutting tips downwards as shown in

Fig. F and ensure the white washer

(26) is fitted to the blade nut.

• Ensure the blade nut (21) is tight.

Note: Your mower is supplied with the blade

height in position E (Fig. G).

• Always re-fit 3 spacers and never fit more

or your mower will become unsafe.

Carrying your mower

Disconnect your mower from the mains.

Remove the grassbox (if fitted), lower the handle to

the flat “park” position and then, holding one handle

near the pivot block and carry with the blade pointing

away from you.

How to use your mower (Fig. H & J)

Observe all the relevant warnings when

using your mower.

We recommend the directional method of

operation to obtain maximum cutting

performance from your mower and to reduce

the risk of the trailing extension lead from

entering the cutting path.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GX302 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info