Bedienungsanleitung Black Decker GX302 (Seite 7 von 47) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Spanisch)

474472

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

ENGLISH

Overload protection

Your mower is fitted with overload protection.

The reset button (33) can be found on the switch box

(Fig. A).

If you work too quickly in long grass, or in heavy

cutting conditions, you may overload the motor.

This will be indicated by a significant drop in speed,

and eventually the overload protection will operate.

This is not a fault but a safety device to protect

your mower.

When this occurs, release the switch and wait for

2 to 3 minutes to allow the motor to cool, then press

the reset button (33) and restart by operating the

switch lever.

If the cut-out operates again within 10 minutes you

should increase the height of cut (see “Height of cut

adjustment”) and walk more slowly.

Severe overloading may result in a longer delay on

restarting. In such cases, after resetting, you should

allow the motor to cool.

Blade maintenance

Steel blades

The steel blade is designed to give a fine

finish in long or tough grass. The blade will

continue to cut even when it has become

blunt or burred. There is no need for it to be

razor sharp.

If, however, because of damage or wear the

cutting performance deteriorates, then your

mower may require a new blade, or at least

the existing blade to be sharpened.

We recommend that the steel blade is

sharpened or a new blade fitted at the

beginning of each season.

Plastic blades

Plastic blades will wear during use. This type

of blade cannot be sharpened and should be

discarded and new blades fitted when worn.

Note: Plastic blades should be replaced in

pairs, not singly.

A number of spare blades are supplied with

the plastic blade cutting system when

purchased separately.

Replacement blades are available from

Black & Decker service agents.

Warning! When fitting a new blade use only

the Black & Decker replacement part

specified for your mower - do not attempt to

fit any other blade.

Fitting a new blade

Observe all the relevant warnings before

changing blades.

Details on the fitment of new steel blades are

given in “Cut height adjustment”. Details on

the fitment of new plastic blades are given in

“Changing to the plastic blade system”.

Handy hints

• Before starting your mower on grass always tilt it

to one side slightly and allow it to run up to

maximum speed before commencing to cut the

grass. This will maximise the hover effect and will

prevent the blades from digging into the grass.

• On long grass, above 10cm (4 inches), use two

cuts to get a close finish. We recommend that

the first cut should be taken with the blade set at

maximum height of cut and the second taken

with it set at medium or close. This will prove to

be easier and give a better overall finish to

your lawn.

Care and maintenance

The advice given in this section covers the

general care and maintenance of the main

body of your mower. Advice relating to the

blades is given in “Maintenance of blades”.

Warning! Do not use a cable which

shows signs of damage. Fit a new cable

completely - do not make any permanent or

temporary repairs.

• Always keep your mower clean and free

from grass cuttings, especially the

underside of the cutter cover and the air

vents.

• Check all electrical cables at regular

intervals, looking for signs of wear,

abrasion or other damage.

• At the end of each cutting session we

recommend that the build up of grass on

the underside of the cutter cover is

removed using a blunt scraper or the

spanner supplied.

• Remove grass cuttings from the slot

between the pivot block flanges.

• Clean all plastic components with a

damp cloth.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GX302 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info