Bedienungsanleitung Black Decker ka 270 (Seite 8 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

389404

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

ENGLISH

Fitting sanding sheets (fig. F)

◆ Detach the two diamond-shaped tips (18) from the

sanding sheet (19).

◆ Hold the tool with the sanding base facing upwards.

◆ Place the sanding sheet (19) onto the sanding base,

making sure that the holes in the sheet line up with the

holes in the base.

The diamond-shaped tip (18) can be reversed and replaced

when worn.

◆ When the front part of the tip is worn, detach it from the

sheet, reverse it and press it onto the sanding base again.

◆ When the whole tip is worn, remove it from the sanding

base and fit a new tip.

Tip of the sanding base (fig. G)

When the sanding base tip (6) is worn, it can be reversed or

replaced. When the tip holder (5) is worn, it can be replaced.

Spare parts are available from your Black & Decker dealer.

◆ Remove the screw (20).

◆ Reverse or replace the worn part.

◆ Fit and tighten the screw.

Finger attachment (fig. H)

The finger attachment is used for fine detail sanding.

◆ Remove the screw (20).

◆ Remove the diamond-shaped tip holder (5) from the

sanding base.

◆ Fit the finger attachment (10) onto the sanding base.

◆ Fit and tighten the screw.

◆ Fit the appropiate sanding sheet (21) onto the finger

attachment.

Profile attachment

The profile attachment is used for contour sanding.

Fitting the profile attachment (fig. I)

◆ Remove the screw (20).

◆ Remove the diamond-shaped tip holder (5) from the

sanding base.

◆ Fit the profile attachment (8) onto the sanding base.

◆ Fit and tighten the screw.

Fitting and removing a sanding profile (fig. J1 & J2)

◆ Choose the sanding profile most suitable for your application.

◆ Place one end of the sanding profile (9) into the recess at

the front end of the profile attachment (8).

◆ Push the other end of the sanding profile until it clicks

into place.

◆ To remove the sanding profile (9), push it forward and pull

the rear end out of the profile attachment (8).

Fitting a sanding sheet onto a sanding profile (fig. K)

◆ Align the sanding sheet (22) with the sanding profile (9).

◆ Press the sanding sheet onto the sanding profile, making

sure that the sanding sheet follows the shape of the profile.

Louvre attachment (fig. L & M)

With the louvre attachment you can work in crevices.

◆ Remove the screw (20).

◆ Remove the diamond-shaped tip holder (5) from the

sanding base.

◆ Fit the louvre attachment (12) onto the sanding base.

◆ Fit and tighten the screw.

◆ Fit the appropiate sanding sheet (23) onto the louvre

attachment.

The additional piece of velcro fastener (24) can be attached to

the top surface of the louvre attachment (12) to allow for

sanding using both sides.

◆ Remove the backing paper from the velcro fastener (24).

◆ Stick the velcro fastener to the top surface of the louvre

attachment.

◆ Fit the sanding piece (23) to the velcro fastener.

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Do not cover the ventilation slots when using the

tool. Hold the tool as shown in fig. Q. Make sure that the

sanding base is flat on the workpiece.

Switching on and off (fig. N)

◆ To switch the tool on, set the on/off switch (1) to position I.

◆ To switch the tool off, set the on/off switch to position O.

Automatic brake system (ABS)

This tool has an automatic brake system. When the tool is not

on the work surface, this feature keeps the speed of the disc

below the speed of the motor. When the tool is switched off,

the disc will stop very quickly.

Emptying the dust cassette (fig. O & P)

The dust cassette should be emptied every 10 minutes of use.

◆ Pull the dust cassette (3) to the rear and off the tool.

◆ Remove the cover (25) by twisting it counterclockwise.

◆ Hold dust cassette with the filter (26) facing down and

shake the cassette to empty the contents. Shake the

cover to empty the contents.

◆ Refit the cover (25) onto the dust cassette, twisting it

clockwise until it locks into place.

◆ Refit the dust cassette onto the tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker ka 270 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info