Bedienungsanleitung Black Decker KA150 (Seite 22 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

21667

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

PREPARING YOUR MOUSE

To prepare your Mouse, proceed as follows:

Disconnect the plug from the electricity supply.

Fit the appropriate abrasive or accessory to the base of

the tool and connect the dust extraction outlet to a

vacuum cleaner.

USING YOUR MOUSE WITH THE POINTED BASE

Your Mouse is equipped

with a teardrop base

which allows you to use

it on large flat surfaces,

as well as difficult and

confined areas.

FITTING THE ABRASIVE

Your Mouse uses pre-cut nylon backed sheets of

abrasive of a specific size.

To fit the abrasive proceed as follows:

Disconnect the plug from the electricity supply.

Press the nylon loop side

of the abrasive against

the hooks on the base.

Align the holes in the

abrasive (where fitted)

with the dust extraction

holes in the base of the

Mouse. Ensure the

abrasive evenly overlaps the base. Never use your

Mouse without an abrasive or accessory. The abrasive

supplied with your tool has two replacement tips

supplied. In addition, the abrasive is designed to allow

you to interchange and or rotate the diamond tip.

To rotate the diamond tip,

remove the tip, rotate it

through 180˚ and press it

back on the hook base as

shown. Note: Remove the

two replacement tips

from the abrasive before

using the Mouse, these

can be used later when the original diamond tip wears.

FITTING THE FINGER ATTACHMENT BASE (KA150K)

Disconnect the plug from

the electricity supply.

First remove the abrasive

and then remove the 2

small screws in the

Mouse base using the

screwdriver provided.

Looking from the bottom

of the Mouse rotate the

base in a clockwise

direction whilst holding

the Mouse in one hand

and the base in the other.

The base can be lifted off

and removed.

Take the finger

attachment base and

locate the three legs into

the location holes in the

Mouse. Turn the finger

attachment base anti

clockwise as shown to attach the base. The finger

should point directly from the front of the Mouse.

Replace the small screws into the base of the finger

attachment base. Note: The screws must be placed

back into the base for the unit to work properly.

DUST EXTRACTION

Your Mouse has an adaptor to connect it to a vacuum

cleaner when sanding wood.

To connect to the vacuum cleaner, proceed as follows:

Disconnect the plug from the electricity supply.

Insert the adaptor into

the rear outlet of the

Mouse and connect the

hose of a vacuum

cleaner.

OPERATING YOUR MOUSE

To switch your Mouse

on, press the on/off

switch on the side

marked “I”.

To switch your Mouse

off, press the on/off

switch on the side “0”.

Before plugging your

Mouse in to the electricity supply, make sure it is

switched off on your Mouse.

HANDY HINTS

• Do not apply excessive pressure when you use

your Mouse.

• Replace the abrasive when it is worn.

• Use high grit abrasive for a fine finish.

KA150K ML p19-33 21-09-2000, 13:5522

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KA150 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info