Bedienungsanleitung Black Decker kc 2000 fm (Seite 7 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

383577

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ENGLISH

Warning! Do not charge the battery at ambient temperatures

below 4 °C or above 40 °C. Recommended charging temperature:

approx. 24 °C.

◆ To charge the battery (5), remove it from the tool and

insert it into the charger (12). The battery will only fit into

the charger in one way. Do not force. Be sure that the

battery is fully seated in the charger.

◆ Plug in the charger.

◆ Check if the red charging indicator (13) lights up. If the

green end of charge indicator (14) lights up now instead,

the battery is too hot and cannot be charged.

If this happens, remove the battery from the charger, let

the battery cool down for approx. 1 hour and re-insert it.

After approx. 1 hour of charging, the red charging indicator (13)

will stop lighting and the green end of charge indicator (14)

will light up. The battery is now fully charged.

◆ Remove the battery from the charger.

Selecting the torque or drill position (fig. E)

This tool is fitted with a collar to set the torque for tightening

screws.

u For drilling, set the collar (7) to the drilling position by

aligning the symbol

with the marking (21).

◆ For screwdriving, set the collar to the desired setting.

If you do not yet know the appropriate setting, proceed as

follows:

◆ Set the collar (7) to position 1.

◆ Tighten the first screw.

◆ If the clutch ratchets before the desired result is

achieved, increase the collar setting and continue

tightening the screw. Repeat until you reach the correct

setting. Use this setting for the remaining screws.

Selecting the direction of rotation (fig. A)

For drilling, sawing, sanding and tightening screws, use forward

(clockwise) rotation. For loosening screws or removing a jammed

drill bit, use reverse (counterclockwise) rotation.

◆ To select forward rotation, push the forward/reverse

slider (2) to the left.

◆ To select reverse rotation, push the forward/reverse slider

to the right.

◆ To lock the tool, set the forward/reverse slider into the

centre position.

Drilling/screwdriving (fig. A)

◆ Select forward or reverse rotation using the forward/

reverse slider (2).

◆ To switch the tool on, press the variable speed switch (1).

The tool speed depends on how far you press the switch.

◆ To switch the tool off, release the variable speed switch.

Setting the sawing angle (fig. F & H)

The saw shoe can be set to angles of 0° (straight) and 45°

(right-side bevel).

◆ Lock the tool by setting the forward/reverse slider (2) to

the centre position (fig. F).

◆ Loosen the screw (19) until the shoe can move freely (fig. H).

◆ Pull the saw shoe forward and tilt it into the required angle.

◆ Tighten the screw (19).

Sawing (fig. F)

◆ Select forward rotation by moving the forward/reverse

slider (2) to the left.

◆ To switch the tool on, keep the lock-off button (9)

depressed and press the variable speed switch (1).

The tool speed depends on how far you press the switch.

◆ Release the lock-off button (9).

◆ To switch the tool off, release the variable speed switch.

Sanding (fig. A)

◆ Select forward rotation by moving the forward/reverse

slider (2) to the left.

◆ To switch the tool on, press the variable speed switch (1).

The tool speed depends on how far you press the switch.

◆ To switch the tool off, release the variable speed switch.

Hints for optimum use

Drilling

◆ Always apply a light pressure in a straight line with the

drill bit.

◆ Just before the drill tip breaks through the other side of

the workpiece, decrease pressure on the tool.

◆ Use a block of wood to back up workpieces that may splinter.

◆ Use spade bits when drilling large diameter holes in wood.

◆ Use HSS drill bits when drilling in metal.

◆ Use masonry bits when drilling in soft masonry.

◆ Use a lubricant when drilling metals other than cast iron

and brass.

◆ Make an indentation using a centre punch at the centre of

the hole to be drilled in order to improve accuracy.

Screwdriving

◆ Always use the correct type and size of screwdriver bit.

◆ If screws are difficult to tighten, try applying a small

amount of washing liquid or soap as a lubricant.

◆ Always hold the tool and screwdriver bit in a straight line

with the screw.

Sawing

◆ Always use the appropriate type of saw blade for the

workpiece material and type of cut.

◆ If necessary, drill a hole near the starting point of the cut.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker kc 2000 fm Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info