Bedienungsanleitung Black Decker kc 2000 fm (Seite 8 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

383577

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ENGLISH

When sawing wooden workpieces, it is not necessary to drill a

pilot hole:

◆ Mark the desired starting point.

◆ Tilt the tool forward and place the rounded front edge of

the saw shoe on the workpiece.

◆ Switch the tool on and slowly feed the saw blade into the

workpiece at the desired starting point.

When cutting sheet metal:

◆ Clamp a piece of plywood or soft wood to the back of the

workpiece and saw through the combination in order to

obtain a clear cut.

◆ Do not force the saw blade into the workpiece. Note that

cutting sheet metal will normally take more time than

sawing thicker wooden workpieces.

◆ Spread a thin film of oil along the cutting line before sawing.

◆ To cut, switch the tool on and move it down until the saw

blade is exactly over the point of entry.

Lower the rear of the shoe towards the workpiece,

maintaining a firm pivoting pressure on the saw shoe.

With the shoe flat on the workpiece, feed the blade into

the workpiece.

When cutting laminates:

◆ Cut thin laminates with the back surface facing up,

as splintering is most likely to occur on the side of the

workpiece facing the saw shoe.

◆ For clean cuts, clamp a piece of plywood or hardboard to

both sides of the laminate and cut through the resulting

sandwich.

Sanding

◆ Do not exert too much pressure on the tool.

◆ Regularly check the condition of the sanding sheet.

Replace when necessary.

◆ When sanding new layers of paint before applying

another layer, use extra fine grit.

◆ On very uneven surfaces, or when removing layers of

paint, start with a coarse grit. On other surfaces, start

with a medium grit. In both cases, gradually change to a

fine grit for a smooth finish.

◆ Consult your retailer for more information on available

accessories for sanding, polishing, stripping and scrubbing.

Maintenance

Your Black & Decker tool has been designed to operate over a

long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regular cleaning.

Your charger does not require any maintenance apart from

regular cleaning.

Warning! Before performing any maintenance on the tool,

remove the battery from the tool. Unplug the charger before

cleaning it.

◆ Regularly clean the ventilation slots in your tool and

charger using a soft brush or dry cloth.

◆ Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

◆ Regularly open the chuck and tap it to remove any dust

from the interior.

◆ Regularly apply a drop of light machine oil to the guide

roller (22) of the jigsaw head (fig. K).

Protecting the environment

Tools

Black & Decker provides a facility for recycling

Black & Decker products and rechargeable batteries

once they have reached the end of their working life.

This service is provided free of charge. To take

advantage of this service please return your product

to any authorised repair agent who will collect them

on our behalf.

Batteries

Black & Decker batteries can be recharged many

times. At the end of their useful life, discard

batteries with due care for our environment:

◆ Run the battery down completely, then remove it from the

tool.

◆ NiCd and NiMH batteries are recyclable. Take them to

any authorised repair agent or a local recycling station.

You can check the location of your nearest authorised repair

agent by contacting your local Black & Decker office at the

address indicated in this manual. Alternatively, a list of

authorised Black & Decker repair agents and full details of our

after-sales service and contacts are available on the Internet

at: www.2helpU.com.

Technical data

KC2000 KC2002

Voltage V

12 14.4

Battery cat. no. A9275 $

Drill/screwdriver:

No-load speed min

-1

0 - 700 0 - $

Max. torque Nm 6.2 $

Chuck capacity mm 10 10

Max. drilling capacity in steel/wood mm 10/25 10/25

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker kc 2000 fm Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info