Bedienungsanleitung Black Decker kd 664 re (Seite 23 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

387033

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

FITTING THE DRILL BIT (KEYED CHUCKS)

Proceed as follows:

Disconnect the plug from the electricity supply.

Rotate the barrel

of the chuck until

the jaws are

sufficiently open.

Insert the drill bit

in the jaws of the

chuck. Insert the

chuck key with

the end of the chuck key in one of the three holes in the

body of the chuck and the head of the chuck key

engaged with the barrel of the chuck. Turn the chuck

key clockwise to tighten the jaws and securely grip the

drill bit. Remove the chuck key.

REMOVING THE CHUCK (KEYLESS CHUCKS)

Proceed as follows:

To remove the chuck,

open the jaws, hold

it firmly in one hand

and with a screwdriver

held in the other hand,

turn the set-screw in

the chuck clockwise

approximately one

turn, to loosen it.

Place an allen key in

the chuck and tighten the jaws. Give the allen key a

short powerful blow in an anti-clockwise direction with

a hammer to loosen the chuck on the spindle. Remove

the allen key. Use the screwdriver to turn the set-

screw clockwise until it totally disengages from the

spindle. Remove the chuck from the spindle by rotating

it anti-clockwise. To fasten the chuck, put it on the

thread and turn it clockwise until it stops. Put in the

screw and turn it anti-clockwise until absolutely firm.

REMOVING THE CHUCK (KEYED CHUCKS)

Proceed as follows:

To remove the chuck,

open the jaws of the

chuck with the chuck

key. Hold the chuck

firmly in one hand, and

with a screwdriver

turn the screw set in

the chuck clockwise

with the other hand

until it comes out.

Use only the correct chuck key. Place the chuck key

into the chuck, and hold the drill firmly in one hand with

the chuck pointing away from you. Rotate the chuck so

that the chuck key is just above the horizontal position

on the right hand side of the machine. Give the

crossbar end of the key a sharp downward blow with a

mallet or light hammer. The chuck should now be

sufficiently loose to be unscrewed by hand.

FITTING THE SIDE HANDLE

Proceed as follows:

To assemble the

side handle, fit the

bolt in the clamp

and the nut in the

handle. Loosely

assemble the

handle and clamp.

Position the side

handle on the

body of your drill.

Rotate the handle

around the body

of your drill until it

is in the desired

position. Tighten the handle by turning clockwise.

PREPARING YOUR DRILL FOR OPERATION

Proceed as follows:

Fit the correct

accessory for the job.

Set the speed of your

drill. On two-speed

drills, set the two-

speed switch to ‘1’

(low-speed) or ‘2’

(high-speed), or set

the variable speed

control to the desired

speed. As a general

rule, for large size drill bits use low speeds and for

smaller drill bits use high speeds.

Set the forward/

reverse switch to the

desired direction of

rotation. Never change

the setting of the

hammer switch, the

speed switch or the

forward/reverse when

your drill is operating.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker kd 664 re Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info