Bedienungsanleitung Black Decker KS55 T1 (Seite 6 von 12) (Englisch)

579748

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Safety instructions for saws with a pendulum blade guard

◆ Check lower guard for proper closing before each

use. Do not operate the saw if lower guard does not

move freely and close instantly. Never clamp or tie

the lower guard into the open position. If saw is

accidentally dropped, lower guard may be bent.

Raise the lower guard with the retracting handle and

make sure it moves freely and does not touch the blade or

any other part, in all angles and depths of cut.

◆ Check the operation of the lower guard spring. If

the guard and the spring are not operating properly,

they must be serviced before use. Lower guard may

operate sluggishly due to damaged parts, gummy

deposits, or a build-up of debris.

◆ Lower guard should be retracted manually only for

special cuts such as “plunge cuts” and “compound

cuts.” Raise lower guard by retracting handle and

as soon as blade enters the material, the lower

guard must be released. For all other sawing, the lower

guard should operate automatically.

◆ Always observe that the lower guard is covering

the blade before placing saw down on bench or

floor. An unprotected, coasting blade will cause the saw

to walk backwards, cutting whatever is in its path. Be

aware of the time it takes for the blade to stop after

switch is released.

Additional safety instructions for all saws with riving knife

◆ Use the appropriate riving knife for the blade being

used. For the riving knife to work, it must be thicker than

the body of the blade but thinner than the tooth set of the

blade.

◆ Adjust the riving knife as described in this instruction

manual. Incorrect spacing, positioning and alignment can

make the riving knife ineffective in preventing kickback.

◆ Always use the riving knife except when plunge

cutting. Riving knife must be replaced after plunge cutting.

Riving knife causes interference during plunge cutting and

can create kickback.

◆ For the riving knife to work, it must be engaged in

the workpiece. The riving knife is ineffective in

preventing kickback during short cuts.

◆ Do not operate the saw if riving knife is bent. Even a

light interference can slow the closing rate of a guard.

Additional safety instructions for circular saws

◆ Wear ear protectors. Exposure to noise can cause hearing

loss.

◆ Preferably wear a dust mask.

◆ Do not use blades of larger or smaller diameter than

recommended. For the proper blade rating refer to the

technical data. Use only the blades specified in this

manual, complying with EN 847-1.

◆ Never use abrasive cut-off wheels.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

◆ This appliance is not intended for use by young or infirm

persons without supervision. Children must be supervised

to ensure they do not play with the appliance.

◆ If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Overview

1. On/off switch

2. Lock-off button

3. Main handle

4. Secondary handle

5. Locking knob for depth of cut adjustment

6. Depth of cut scale

7. Locking knob for mitre angle adjustment

8. Mitre angle scale

9. Saw blade guard

10. Retracting lever for saw blade guard

11. Saw shoe

12. Parallel fence

13. Riving knife

14. Window (KS65K)

15. Sight guide (KS65K)

16. Spindle lock (KS65K)

17. Saw dust outlet

Assembly

Warning! Before attempting any of the following operations,

make sure that the tool is switched off and unplugged and

that the saw blade has stopped.

Removing and fitting a saw blade (fig. A)

Removing

◆ Insert a screwdriver into the hole (18) to prevent the saw

blade from rotating. KS65K: keep the spindle lock (16)

depressed.

◆ Loosen and remove the blade retaining screw (20) by

turning it counterclockwise using the spanner supplied.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KS55 T1 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker KS55 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info