Bedienungsanleitung Black Decker KS55 T1 (Seite 7 von 12) (Englisch)

579748

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

◆ Remove the outer washer (19).

◆ Remove the saw blade (21).

Fitting

◆ Place the saw blade onto the inner washer (22), making

sure that the arrow on the blade points in the same

direction as the arrow on the tool.

◆ Fit the outer washer (19) on the spindle, with the raised

part pointing away from the saw blade.

◆ Insert the blade retaining screw (20) into the hole.

◆ Insert a screwdriver into the hole (18) to prevent the saw

blade from rotating. KS65K: keep the spindle lock (16)

depressed.

◆ Securely tighten the blade retaining screw by turning it

clockwise using the spanner supplied.

◆ Adjust the riving knife as described below.

Adjusting the riving knife (fig. B)

The riving knife prevents the saw blade from jamming during

rip sawing operations. The riving knife must be adjusted after

replacing the saw blade.

◆ KS64(K)/KS65K: set the saw shoe to the minimum depth

of cut as described below. KS55: the screws (23) can be

accessed through the holes in the guard.

◆ Loosen the two screws (23).

◆ Position the riving knife (13) as shown.

– The distance between the toothed rim and the riving

knife should be 2 - 3 mm.

– The height difference between the toothed rim and the

lower end of the riving knife should be 2 - 3 mm.

◆ Tighten the screws (23).

Fitting and removing the parallel fence (fig. C)

The parallel fence is used to saw in a straight line parallel to

the edge of the workpiece.

Fitting

◆ Loosen the locking knob (24).

◆ Insert the parallel fence (12) through the openings (25).

◆ Slide the parallel fence into the desired position.

◆ Tighten the locking knob.

Removing

◆ Loosen the locking knob (24).

◆ Pull the parallel fence off the tool.

Use

Warning! Let the tool work at its own pace. Do not overload.

This tool can be used in the right hand or the left hand.

Warning! Carefully guide the cable in order to avoid

accidentally cutting it.

Adjusting the depth of cut (fig. D)

The depth of cut should be set according to the thickness of

the workpiece. It should exceed the thickness by approx. 2 mm.

◆ Loosen the knob (5) to unlock the saw shoe.

◆ Move the saw shoe (11) into the desired position.

The corresponding depth of cut can be read from the scale (6).

◆ Tighten the knob to lock the saw shoe in place.

Adjusting the mitre angle (fig. E)

This tool can be set to mitre angles between 0° and 45°.

◆ Loosen the locking knob (7) to unlock the saw shoe.

◆ Move the saw shoe (11) into the desired position.

The corresponding mitre angle can be read from the scale (8).

◆ Tighten the locking knob to lock the saw shoe in place.

Switching on and off

Warning! Before switching on, make sure that the spanner

has been removed from the blade retaining screw and that the

screwdriver has been removed from the tool.

Switching on

◆ Keep the lock-off button (2) depressed and press the

on/off switch (1).

◆ Release the lock-off button.

Switching off

◆ Release the on/off switch.

KS55/KS64(K) - Aligning the saw with the cutting line

(fig. F)

The saw is equipped with guides for straight cutting (26) and

guides for 45° mitre cutting (27).

◆ Align the left edge of the guides (26) or (27) with the

cutting line (28).

For very accurate cuts:

◆ Mark a cutting line on a scrap piece of wood.

◆ Align the left edge of the guides (26) or (27) with the

cutting line (28).

◆ Make a test cut.

◆ Depending on the results, adjust the position of the

guides relative to the cutting line.

KS65K - Adjusting the sight guide (fig. G)

◆ While viewing through the window (14), align the saw

blade teeth with the cutting line.

◆ While keeping the saw in this position, loosen the sight

guide (15) on the saw shoe (11) as shown.

◆ Align the 0° mark (29) on the sight guide with the cutting

line (31). When adjusting for 45° mitre cuts, align the 45°

mark (30) on the sight guide with the cutting line.

◆ Secure the sight guide using the screw (32).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KS55 T1 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker KS55 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info