Bedienungsanleitung Black Decker KS901SE T1 (Seite 7 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

581015

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

 Position 0: metal and aluminium and sheet metal (no pendulum action).

 Position 1: for laminates, hard wood, work tops.

 Position 2: for plywood and PVC/Plastics.

 Position 3: for soft wood and fast cutting

To adjust the pendulum action:

 Rotate the Pendulum Stroke dial (6) to the required position.

Sawing

Hold the tool  rmly with both hands while cutting.

The shoe plate (4) should be held  rmly against the material being cut. This will help prevent

Auto Select™ dial ( g. F - KS801SE and KS901SE only)

The KS801SE and KS901SE are  tted with a unique Auto Select™ Dial (6) to set the speed and the pendulum action

for various cutting applications.

To select the optimum speed and pendulum action for the type of material being cut, rotate the dial (6) as shown

in the table below:

Icon Speed Pendulum Application

Slow No Straight and curved cuts – sheet metal, tin plate,

ceramic tiles and  breglass sheet

PVC

Medium Medium / low Straight and curved cuts – hardwood, decking,

 ooring, plastic, pexiglas and PVC

Fast Maxiumum Straight cuts – general lumber and softwood

Fast Medium / low Straight and curved cuts – plywood and wood panels

Fast No Straight and curved cuts – countertops, laminate

boards, scrolling, curves and craftwork

PVC

the saw from jumping, reduce vibration and minimise blade

breakage.

 Let the blade run freely for a few seconds before starting

the cut.

 Apply only a gentle pressure to the tool while performing

the cut.

Hints for optimum use

Straight Assist Blade

When you require a straight cut with extra precision, use the

straight assist blade. The KS901SE/PE is supplied with this

blade as standard and it can be purchased as an optional

extra for use with the KS801SE (part number X21001-XJ).

Anti-Splinter Guard ( g. G

- KS901SE only

)

To minimise splintering, use the anti-splinter guard supplied

with your product. This reduces the open area between the

shoe and the blade without restricting your view of the cut line.

To  t the anti-splinter guard:

 Remove the blade (see  gure A).

 Line up the anti-splinter guard (13) with the shoe plate (4)

from underneath.

 Press down onto the shoe plate until the guard clicks in

place.

 Replace the blade.

Sawing laminates

When cutting laminates, splintering may occur which can

damage the presentation surface. The most common saw

blades cut on the upward stroke, therefore if the shoe plate is

sitting on the presentation surface either use a saw blade that

cuts on the downward stroke or:

 Use a  ne-tooth saw blade.

 Saw from the back surface of the workpiece.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KS901SE T1 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info