Bedienungsanleitung Black Decker KS901SE T1 (Seite 8 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

581015

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

 To minimise splintering, clamp a piece of scrap wood or

hardboard to both sides of the workpiece and saw through

this sandwich. Alternatively,  t the anti-splinter guard (13)

that is supplied with your product. (KS901SE only).

Sawing metal

Warning! Do not use a vacuum when cutting metal. Metal

 lings will be hot and may cause  re.

Be aware that sawing metal takes much more time than

sawing wood.

 Use a saw blade suitable for sawing metal.

 When cutting thin sheet metal, clamp a piece of scrap

wood to the back surface of the workpiece and cut

through this sandwich.

 Spread a  lm of oil along the intended line of cut.

Rip Fence

Ripping and circle cutting without a pencil line are easily done

with a rip fence and circle guide (available as an optional extra

- part number X43005-XJ).

Attaching Rip Fence ( gs. H & I)

 Insert rip fence (14) into the shoe plate slots with the cross

bar facing down as shown in  gure H.

 Place screw (15) into hole in bottom of shoe plate.

 Align clamp bar (16) over screw with lipped edge facing

down and pointing towards the rear of the saw.

 Using a phillips screwdriver, run the screw into the

threaded hole in the bar clamp as shown in  gure I.

 Adjust to width of cut and tighten screw.

Circle Cutting ( g. J)

 Insert rip fence into slot on the right side of shoe plate

with cross bar facing up.

 Adjust rip fence so that distance from blade to hole

in cross bar is the desired radius and tighten screw.

 Place saw so that centre of hole in cross bar is over

centre of circle to be cut (make plunge cut, drill hole for

blade or cut inward from edge of material to get blade

into position).

 When saw is properly positioned, drive a small nail

through hole in cross bar into exact centre of circle

to be cut.

 Using rip fence as a pivot arm, begin cutting circle.

Plunge Cutting ( g. K)

A plunge cut is an easy method of making an inside cut. The

saw can be inserted directly into a panel or board without

 rst drilling a lead or pilot hole. In plunge cutting, measure

the surface to be cut and mark clearly with a pencil. Next tip

the saw forward until the front end of the shoe sits  rmly on

the work surface and the blade clears the work through its

full stroke. Switch the tool on and allow it to attain maximum

speed. Grip the saw  rmly and lower the back edge of tool

slowly until the blade reaches its complete depth. Hold the

shoe  at against the wood and begin cutting. Do not remove

blade from cut while it is still moving. Blade must come to

a complete stop.

Maintenance

Your BLACK+DECKER tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper

tool care and regular cleaning.

 Regularly clean the ventilation slots in your tool using

a soft brush or dry cloth.

 Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

Never let any liquid get inside the tool and never

immerse any part of the tool into liquid.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be  tted:

 Safely dispose of the old plug.

 Connect the brown lead to the live terminal in the

new plug.

 Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the  tting instructions supplied with good quality plugs.

Recommended fuse: 5 A.

Protecting the environment

Separate collection. This product must not be

disposed of with normal household waste.

Should you  nd one day that your BLACK+DECKER product

needs replacement, or if it is of no further use to you, do

not dispose of it with household waste. Make this product

available for separate collection.

Separate collection of used products and

packaging allows materials to be recycled

and used again.

Re-use of recycled materials helps prevent

environmental pollution and reduces the

demand for raw materials.

Local regulations may provide for separate collection of

electrical products from the household, at municipal waste

sites or by the retailer when you purchase a new product.

BLACK+DECKER provides a facility for the collection and

recycling of BLACK+DECKER products once they have

reached the end of their working life. To take advantage of this

service please return your product to any authorised repair

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KS901SE T1 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info