Bedienungsanleitung Black Decker kw 1600 eka (Seite 10 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

427189

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENGLISH

Use

Warning! Let the tool work at its own pace. Do not overload.

u Carefully guide the cable in order to avoid accidentally

cutting it.

Adjustingthedepthofcut(g.I,J&K)

The depth of cut is the distance X between the depth stop bar

(9) and the depth stop (29). The depth of cut can be set in two

different ways as described below.

Adjustingthedepthofcutusingthescale(g.J)

u Fit the router bit as described above.

u Loosen the locking screw (30).

u Pull the plunge lock lever (5) up.

u Plunge the router down until the router bit touches the

workpiece.

u Push the plunge lock lever (5) down.

u Move the depth stop bar (9) down against the depth stop

using the depth stop adjuster (31). Reset the scale by

aligning the zero marking (32) with the arrow (33).

u Move the depth stop bar (9) to the calculated position

using the depth stop adjuster (31). One quarter turn

corresponds to approx. 6.25 mm.

u Tighten the locking screw (30).

u Fine adjust using the adjusting knob (34). One full turn

corresponds to approx. 1 mm.

u Pull the plunge lock lever (5) up and return the router to its

original position.

u After switching the router on, plunge it down and make the

desired cut.

Adjustingthedepthofcutusingapieceofwood(g.K)

u Fit the router bit and plunge the router down as described

above.

u Loosen the locking screw (30).

u Move the depth stop bar (9) up using the depth stop

adjuster (31).

u Place a piece of wood with a thickness equal to the

desired depth of cut between the depth stop (29) and the

depth stop bar (9).

u Move the depth stop bar (9) down against the wood using

the depth stop adjuster (31).

u Tighten the locking screw (30).

u Fine adjust using the adjusting knob (34).

u Remove the piece of wood.

u Pull the plunge lock lever (5) up and return the router to its

original position.

u After switching the router on, plunge it down and make the

desired cut.

Adjustingtherevolverdepthstop(g.L)

After turning the revolver depth stop to the desired setting, you

can ne-adjust the depth stop to be used. If you want to make

several cuts with a different depth of cut, adjust each of the

depth stops.

u Turn the depth stop screw (35) up or down as required

using a screwdriver.

Setting the speed

u Set the speed control knob (4) to the required speed.

Use a high speed for small diameter router bits. Use a low

speed for large diameter router bits.

Usingabattenasaguide(g.M)

When it is not possible to use the edge guide, for example

when routing grooves in the back panel of a bookcase to

support shelves, proceed as follows:

u Select a piece of wood with a straight edge to use as a

batten.

u Place the batten onto the workpiece.

u Move the batten until it is in the correct position to guide

the tool.

u Securely clamp the batten to the workpiece.

Usingthetemplateguide(g.D)

The template guide can be used to make a cutout shape from

a template, for instance a letter.

u Secure the template over the workpiece with double-sided

tape or ‘G' clamps.

u The router bit must extend below the ange of the

template guide, to cut the workpiece in the shape of the

template.

Usingthedistancepiece(g.E)

The distance piece can be used for trimming wooden or

laminate vertical projections.

Usingthecentringpin(g.F)

The centring pin can be used to cut out circular patterns.

u Drill a hole for the point of the centring pin in the centre of

the circle to be cut.

u Place the router on the workpiece with the point of the

centring pin in the drilled hole.

u Adjust the radius of the circle with the bars of the edge

guide.

u The router can now be moved over the workpiece to cut

out the circle.

Usingthecopyfollower(g.G)

The copy follower helps to maintain an equal cutting distance

along the edge of irregularly shaped workpieces.

u Place the router on the workpiece at the desired distance

from the edge to be copied.

u Adjust the bars of the edge guide until the wheel is in

contact with the workpiece.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker kw 1600 eka Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info