Bedienungsanleitung Black Decker MT3000K T1 (Seite 6 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

578616

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

ENGLISH

Fitting sanding sheets (fig. D)

◆ Detach the two diamond-shaped tips (23) from the

sanding sheet (19).

◆ Hold the tool with the sanding base facing upwards.

◆ Place the sanding sheet (19) onto the sanding base,

making sure that the holes in the sheet line up with the

holes in the base.

The diamond-shaped tip (23) can be reversed and replaced

when worn.

◆ When the front part of the tip is worn, detach it from the

sheet, reverse it and press it onto the sanding base again.

◆ When the whole tip is worn, remove it from the sanding

base and fit a new tip.

Warning! Never use the sanding head without a sanding

sheet or accessory in place.

Tip of the sanding base (fig. E)

When the sanding base tip (8) is worn, it can be reversed or

replaced. Spare parts are available from your Black & Decker

dealer.

◆ Reverse or replace the worn part.

Fitting and removing the scraper head (fig. F)

◆ Slide the scraper head (13) onto the shaft (10).

◆ Align the tab on the clamp plate (11) with the slot in the

shaft.

◆ Fit the clamp plate to the shaft by tightening the screw (24).

◆ To remove the head, remove the screw (19) and the clamp

plate, and pull the head from the shaft.

Removing and fitting the blade cover (fig. G)

◆ Hold the blade cover (14) at the ends.

◆ Lift the blade cover slightly to release it from the screw

(25) and pull the cover off. Take care not to contact the

edges of the blade (26).

◆ To fit the blade cover, hold the cover at the ends and

place it over the claw blade. Push the cover until it snaps

into place.

Warning! Always keep the blade cover in place when the

scraper head is not being used.

Fitting and removing a parallel blade (fig. H)

◆ Select the required parallel blade.

◆ Align the slot on the mounting end of the blade with the

slot in the shaft (10).

◆ Align the tab on the clamp plate (11) with the slot in the

shaft (10) and the blade.

◆ Fit the clamp plate to the shaft by tightening the screw (27).

◆ To remove the blade, remove the screw (19) and the

clamp plate, and take the blade from the shaft.

Replacing the cutting blade (fig. I)

The cutting blade provided with this tool is reversible.

Replacement cutting blades can be obtained from your local

retailer.

◆ Loosen the screw (28) and remove it.

◆ Remove the cutter clamp plate (29).

◆ Reverse the blade (26) so that the unused side comes in

position. If both sides are worn, the blade must be replaced.

◆ Re-install the cutter clamp plate.

◆ Re-fit the screw and tighten it.

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Do not cover the ventilation slots when using the

tool to avoid overheating.

Selecting the direction of rotation (fig. J)

For tightening screws, use forward (clockwise) rotation.

For loosening screws, use reverse (counterclockwise) rotation.

◆ To select forward rotation, press the lock-off button (30)

and push the forward/reverse switch (5) to the left.

◆ To select reverse rotation, press the lock-off button and

push the forward/reverse switch to the right.

Warning! Never change the direction of rotation while the

motor is running.

Switching on and off

◆ To switch the tool on, press the on/off switch (1).

◆ For continuous operation, press the lock-on button (2) and

release the on/off switch.

◆ To switch the tool off, release the on/off switch.

◆ To switch the tool off when in continuous operation,

press the on/off switch once more and release it.

Hints for optimum use

Screwdriving

◆ Always use the correct type and size of screwdriver bit.

◆ If screws are difficult to tighten, try applying a small

amount of washing liquid or soap as a lubricant.

◆ Always hold the tool and screwdriver bit in a straight line

with the screw.

Sanding

◆ Do not exert too much pressure on the tool.

◆ Regularly check the condition of the sanding sheet.

Replace when necessary.

◆ When sanding new layers of paint before applying

another layer, use extra fine grit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker MT3000K T1 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker MT3000K T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info