Bedienungsanleitung Black Decker pp 360 (Seite 5 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

381455

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

ENGLISH

(Original instructions)

Labels on tool

The following pictograms are shown on the tool:

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Additional safety instructions for batteries and

chargers

Batteries

u Never attempt to open for any reason.

u Do not expose the battery to water.

u Do not expose the battery to heat.

u Do not store in locations where the temperature may

exceed 40 °C.

u Charge only at ambient temperatures between

10 °C and 40 °C.

u Charge only using the charger provided with the tool.

u When disposing of batteries, follow the instructions given

in the section "Protecting the environment".

Chargers

u Use your Black & Decker charger only to charge the

battery in the tool with which it was supplied. Other

batteries could burst, causing personal injury and damage.

u Never attempt to charge non-rechargeable batteries.

u Have defective cords replaced immediately.

u Do not expose the charger to water.

u Do not open the charger.

u Do not probe the charger.

The charger is intended for indoor use only.

Read the instruction manual before use.

The charger automatically shuts off if the ambient

temperature becomes too high. As soon as the

ambient temperature has cooled down, the charger

will resume operating.

Charge only at ambient temperatures between

10 °C and 40 °C.

Charging

Electrical safety

Your charger is double insulated; therefore no earth

wire is required. Always check that the mains

voltage corresponds to the voltage on the rating

plate. Never attempt to replace the charger unit with

a regular mains plug.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Overview

1. On/off switch

2. Forward/reverse slider

3. LED light

4. Bit holder

5. Pivot release slider

Fig. A

6. Charger

7. Charger connector

8. Charging indicator

9. Charging base

Assembly

Fitting and removing a screwdriver bit (g. B)

This tool uses screwdriver bits with a 1/4" (6.35 mm)

hexagonal shank.

u To t a bit, insert the bit shaft into the bit holder (4).

u To remove a bit, pull the bit shaft out of the bit holder (4).

Use

u Before rst use, the battery must be charged for 14 hours.

u The battery needs to be charged before rst use and

whenever it fails to produce sufcient power on jobs that

were easily done before. When charging the battery for

the rst time, or after a prolonged storage, it will only

accept an 80% charge. After several charges and

discharge cycles, the battery will attain full capacity.

u Place the tool on the charging base whenever it is not in use.

Charging the battery (g. A)

u Place the tool on the charging base (9).

u Insert the connector (7) into the charging base.

u Plug in the charger (6).

u Leave the tool connected to the charger for 8 - 10 hours.

The red light illuminates when the unit is on charge and will

stay red as long as there is power to the charger. The red light

will not go off to indicate a full charge.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker pp 360 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info