Bedienungsanleitung Black Decker pp 360 (Seite 6 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

381455

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

ENGLISH

(Original instructions)

The charger may hum and become warm while charging;

this is normal and does not indicate a problem.

Generally, a charging time of 8 hours will enable the tool to

operate at an effective power level for most tasks. However,

further charging for up to 10 hours could signicantly increase

the run time, depending on the battery and charging conditions.

Warning! Do not charge the battery at ambient temperatures

below 4 °C or above 40 °C.

Selecting the direction of rotation

For tightening screws, use forward (clockwise) rotation. For

loosening screws use reverse (counterclockwise) rotation.

u To select forward rotation, push the forward/reverse slider

(2) to the left.

u To select reverse rotation, push the forward/reverse slider

(2) to the right.

u To lock the tool, set the forward/reverse button into the

centre position.

Screwdriving

u Select forward or reverse rotation using the forward/

reverse slider (2).

u To switch the tool on, press the on/off switch switch (1).

u To switch the tool off, release the on/off switch (1).

Spindle lock

This tool is tted with a spindle lock so that it can be used as a

normal screwdriver. Use the tool this way to loosen very tight

screws or to rmly tighten screws.

Rotating the gearbox (g. C, D & E)

The tool is tted with a rotating gearbox to facilitate various

screwdriving applications, such as reaching screws in tight

corners and close to ceilings and oors. The bitholder can be

set to a centre position and 3 off-centre positions: top, left and

right. The gearbox and the spindle can be rotated to set the

various bitholder positions.

u To rotate the gearbox (10) push the pivot release slider (5)

forward and turn the gearbox 90° to the left or to the right

(g. C & D). Note: The gearbox will only turn 90° left and

right. Do not attempt to turn any further.

u To rotate the spindle (11) push the pivot release slider (5)

backward and turn the spindle head 180° left or right (g. E).

Warning! Ensure the gearbox and spindle are locked into

place before use.

LED light

The LED light is activated automatically when the trigger is

depressed. The LED will illuminate when the trigger is partially

depressed, before the unit begins running. The LED will also

illuminate when the trigger is depressed and the forward/

reverse slider (2) is in the locked off position (central position).

Hints for optimum use

u Let the tool work at its own pace. Do not overload.

u Always use the correct type and size of screwdriver bit.

u If screws are difcult to tighten, try applying a small

amount of washing liquid or soap as a lubricant.

u Use the auto spindle lock to loosen very tight screws or to

rmly tighten screws.

u Always hold the tool and screwdriver bit in a straight line

with the screw.

u When screwing in wood, it is recommended to drill a pilot

hole with a depth equal to the length of the screw. A pilot

hole guides the screw and prevents splintering or

distortion of the wood. For the optimum size of the pilot

hole, refer to the table below.

u When screwing in hardwood, also drill a clearance hole

with a depth equal to half the length of the screw. For the

optimum size of the clearance hole, refer to the table

below.

Screw size Pilot hole ø Pilot hole ø Clearance

(softwood) (hardwood) hole

No. 6 (3.5 mm) 2.0 mm 2.5 mm 4 mm

No. 8 (4 mm) 3.2 mm 3.5 mm 5.0 mm

No. 10 (5 mm) 3.5 mm 4.0 mm 5.7 mm

Accessories

The performance of your tool depends on the accessory used.

Black & Decker and Piranha accessories are engineered to

high quality standards and designed to enhance the

performance of your tool. By using these accessories you will

get the very best from your tool.

This tool uses screwdriver bits with a 1/4" (6.35 mm)

hexagonal shank.

Maintenance

Your Black & Decker tool has been designed to operate over a

long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regular cleaning.

Your charger does not require any maintenance apart from

regular cleaning.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker pp 360 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info