Bedienungsanleitung Black Decker PS7525 (Seite 8 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

709524

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

(Original instructions)

Electrical safety

This tool is double insulated; therefore no earth wire is

required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Using an extension cable

u Always use an approved extension cable suitable for the

power input of this tool (see technical data). The extension

cable must be suitable for outdoor use and marked ac-

cordingly. Up to 30 m of HO7RN-F 2 X 1.5 mm² extension

cable can be used without loss of product performance.

Before use, inspect the extension cable for signs of

damage, wear and ageing. Replace the extension cable

if damaged or defective. When using a cable reel, always

unwind the cable completely.

Voltage drops

u Under certain power supply conditions this product may-

cause short-time voltage drops during start-up.

u Other equipment may be affected. For example, electri-

clights may temporarily reduce in brightness.

u Contact the supply authority, if necessary, to determine

that the impedance of the power supply is lower than

0.411 ohms. Disturbances are unlikely to occur under this

condition.

Guard against electric shock

u Prevent body contact with earthed or grounded surfaces

(e.g. metal railings, lamp-posts etc.). Electric safety can

be further improved by using a high-sensitivity (30 mA/

30mS) Residual Current Device (RCD).

Features

This tool includes some or all of the following features.

1. On/off switch

2. Lock-off button

3. Power cord retainer

4. Strap clip

5. Angle wheel

6. Pole extension release lever

7. Sprocket cover

8. Locking nut

9. Guide bar

10. Chain

11. Oil resevoir cap

12. Sheath

13. Locking Nut Cap

Assembly

Warning!Before assembly, make sure that the

appliance is switched off and unplugged.

Warning!Always wear protective gloves when

working with pole pruner.

Oiling the chain

You must do this whenever you use a new chain (10) for the

rst time. Take the new chain (10) and soak it in chain oil for at

least an hour before using it. Use BLACK+DECKER chain oil.

We recommend that you use only BLACK+DECKER oil during

the lifetime of your chainsaw because mixtures of different oils

could lead to the oil becoming degraded, which can drastically

shorten the lifetime of the saw chain and create additional

risks.

Never use waste oil, thick oil or very thin sewing machine oil.

These may damage your chainsaw.

Fitting the guide bar and chain (g. A - E)

u Place the pole pruner onto a stable surface.

u Remove Locking Nut Cap (13).

u Unscrew the locking nut (8) counterclockwise to remove

the sprocket cover (7) (g. A).

u Place the chain (10) over the guide bar (9) making sure

that the saw chain cutters are facing the correct direction

by matching the arrow on the chain with the graphic on the

sprocket cover (7) (g. B).

u Place the chain (10) round the sprocket (14) on the saw

while lining up the hole on the guide bar with the chain

adjustment pin (15) (g. C).

u The chain adjustment pin may require re-positioning by

turning the screw (16) (g.D) to align it with the hole in the

guide bar.

u Support the guide bar whilst re-tting the sprocket cover

(7) and the locking nut (8)

u Place the pole pruner onto a stable surface.

u Loosen the locking nut (8) by one full turn using the span-

ner provided

u With a screwdriver turn the screw (16) (g.D), clockwise

increasing the chain tension.

u Check tension by pulling the chain from the chain bar

(g.E).

u Turn the screw clockwise and counter clockwise to

achieve the correct tension. Tension is correct when chain

snaps back to the bar after being pulled 3mm from the

chain bar.

Warning! Do not over tension the chain as this will lead to

excessive wear and will reduce the life of the bar and chain.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker PS7525 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info