Bedienungsanleitung Black Decker RC1050EK T1 (Seite 8 von 12) (Englisch)

581264

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Let the blade run freely for a few seconds before starting

the cut.

Apply only a gentle pressure to the tool while performing

the cut.

If possible, work with the shoe (1) pressed against the

workpiece. This will improve tool control and reduce tool

vibration, as well as prevent the blade from being

damaged.

Hints for optimum use

Sawing wood

Clamp the workpiece securely and remove all nails and

metal objects.

Holding the tool with both hands, work with the shoe (1)

pressed against the workpiece.

Flush cutting (fig. F)

The compact design of the reciprocating saw motor housing

and pivoting shoe permit close cutting to floors, corners and

other difficult areas.

To maximize flush cutting capabilities:

Insert the blade shaft into the blade clamp with the teeth of

the blade facing up.

Turn the saw upside down so you are as close to the work

surface as possible.

Sawing metal (fig. G)

Be aware that sawing metal takes much more time than

sawing wood.

Use a saw blade suitable for sawing metal. Use a fine-tooth

saw blade for ferrous metals and a coarser saw blade for

non-ferrous metals.

When cutting thin sheet metal, clamp a piece of scrap wood

to the back surface of the workpiece and cut through this

sandwich.

Spread a film of oil along the intended line of cut.

Pocket cutting in wood (fig. H)

Measure and mark the required pocket cut.

Fit a saw blade suitable for pocket cutting.

Rest the shoe (1) on the workpiece in such a position that

the blade forms an appropriate angle for the pocket cut.

Switch on the tool and slowly feed the blade into the

workpiece. Make sure that the shoe (1) remains in contact

with the workpiece at all times.

Cutting branches

Branches up to 25 mm in diameter can be cut with this tool.

Warning! Do not use the tool while in a tree, on a ladder or on

any other unstable surface. Be aware of where the branch will

fall.

Cut downward and away from your body.

Make the cut close to the main branch or tree body.

Vertical cutting

The tool allows close cutting to corners and other difficult

areas.

Insert the shank of the saw blade into the blade holder with

the teeth of the blade facing upward.

Hold the tool with the shoe (1) facing downward so that you

are as close to the work surface as possible.

Cut forward and away from your body.

Accessories

The performance of your tool depends on the accessory

used.

Black & Decker and Piranha accessories are engineered to

high quality standards and designed to enhance the

performance of your tool. By using these accessories you

will get the very best from your tool.

Blades

The saw will accept a blade up to 30 cm long. Always use the

shortest blade suitable for your project but long enough to

keep the blade cutting through the material. Longer blades

are more likely to be bent or damaged during use. During

operation some longer blades may vibrate or shake if the

saw is not kept in contact with the workpiece.

Pruning attachment

A pruning attachment is also available for use with your saw.

This accessory attaches to the shoe of the saw and applies

spring loaded pressure to the branch while cutting.

Maintenance

Your Black & Decker tool has been designed to operate over

a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regular cleaning.

Regularly clean the ventilation slots in your tool using a soft

brush or dry cloth.

Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner. Never let

any liquid get inside the tool and never immerse any part of

the tool into liquid.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be fitted:

Safely dispose of the old plug.

Connect the brown lead to the live terminal in the new plug.

Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the fitting instructions supplied with good quality plugs.

Recommended fuse: 10 A.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker RC1050EK T1 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker RC1050EK T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info