Bedienungsanleitung Black Decker STC5433B (Seite 10 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

709494

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISH

(Original instructions)

Assembly

Warning! To reduce the risk of serious personal injury, turn

unit off and remove the battery pack before making any

adjustments or removing/installing attachments or

accessories. An accidental start-up can cause injury.

Assembly tools required

u Phillips Screwdriver (not supplied).

u Hex wrench (supplied).

Installing the guard

Warning! Never operate appliance without the guard (13)

rmly in place. The guard must always be properly attached

on the appliance to protect the user.

u Remove the screw from the guard.

u Turn the trimmer upside down so that you are looking

down at the spool cap ( 20 ).

u Turn the guard (12) upside down and slide it fully onto the

trimmer head (10). Make sure the tabs ( 16 ) on the guard

engage the ribs (17) on the trimmer head as shown.

u Continue to slide the guard on until you hear it “snap”

into place. The locking tab (18) should snap into the

housing slot (19) as shown in gure G.

u Using a phillips screwdriver, insert the guard screw and

tighten securely as shown in gure H to complete the

guard assembly.

u Once the guard is installed, remove the covering from

the line cut-off blade, located on the edge of the guard.

Assembling the Pole

u To assemble the pole, line up the upper trimmer pole

(6) and the lower trimmer pole (7) as shown in gure I.

Press down the latching button (20) and slide the upper

pole into the lower pole. Ensure the latching button

engages the latch hole (21).

u Secure the poles by tightening the middle bolt (22) with

the supplied hex wrench (23) as shown in gure J.

Attaching the auxiliary handle

u Place the auxiliary handle (5) onto the top of the upper

trimmer pole (6) as shown in gure K.

u Slide the bracket (24) of the auxiliary handle onto the

bottom of the handle.

u Thread the handle bolts (25) through the handle and

into the bracket from above.

u Tighten the handle bolts. Ensure the handle is securely

attached by closing the handle clamp (26).

u To adjust the position of the auxiliary handle, open the

handle clamp and slide the handle up and down the

pole until it is in the desired location. Close the clamp to

lock the handle in place.

Releasing the cutting line

For shipping purposes, the cutting line is taped to the spool

housing.

u Remove the tape holding the cutting line to the spool

housing. See "Replacing the Spool" for instructions for

removing the spool.

Charging procedure (STC5433 unit only)

BLACK+DECKER chargers are designed to charge

BLACK+DECKER battery packs.

u Plug the charger (15) into an appropriate outlet before

inserting the battery pack (14).

u Insert the battery pack (14) into the charger (15) as shown

in gure A.

u The green LED (15a) will ash indicating that the battery is

being charged.

u The completion of charge is indicated by the green LED

(15a) remaining on continuously. The pack is fully charged

and may be used at this time or left on the charger.

Note: Recharge discharged batteries as soon as possible

after use or battery life may be greatly diminished. For longest

battery life, do not discharge batteries fully.

It is recommended that the batteries be recharged after each

use.

Leaving the battery in the charger

The charger (15) and battery pack (14) can be left connected

with the LED glowing indenitely. The charger will keep the

battery pack fresh and fully charged.

Important charging notes

u Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 65°F and 75°F (18°- 24°C). DO NOT charge the

battery pack in an air temperature below +40°F (+4.5°C),

or above +105°F (+40.5°C). This is important and will

prevent serious damage to the battery pack.

u The charger and battery pack may become warm to touch

while charging. This is a normal condition, and does not

indicate a problem. To facilitate the cooling of the battery

pack after use, avoid placing the charger or battery pack

in a warm environment such as in a metal shed, or an

uninsulated trailer.

u If the battery pack does not charge properly:

u Check current at receptacle by plugging in a lamp or

other appliance.

u Check to see if receptacle is connected to a light switch

which turns power off when you turn out the lights.

u Move charger and battery pack to a location where the

surrounding air temperature is approximately 65°F

- 75°F (18°- 24°C).

u If charging problems persist, take the tool, battery pack

and charger to your local service center.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker STC5433B Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info