Bedienungsanleitung Black Decker vpx 1212 (Seite 7 von 97) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

388366

Zoom out

Zoom in

Vorherige Seite

1/97

Nächste Seite

ENGLISH

X Charge discharged batteries within 1 week. Battery life

will be greatly diminished if stored in a discharged state.

Charge indicators

If the charger detects a problem with a battery pack, the

charge indicator (11) will flash at a fast rate.

X If this occurs, re-insert the battery pack (9).

X If the problem persists, put a different battery pack in the

charger to determine if the charger is OK.

X If the new battery pack charges correctly, then the

original battery pack is defective and should be returned

to a service centre for recycling.

X If the new battery pack gives the same indication as the

original, take the charger to be tested at an authorized

service centre.

Note: It may take as long as fifteen minutes to determine that

the pack is defective.

If the battery pack is too hot or too cold, the LED will

alternately blink fast and slow, one flash at each speed and

repeat.

Battery chargers - daisy chaining (fig. C)

Single and dual port chargers can be electrically connected

in any order up to a maximum of 4 chargers. Each charger

has a power-in cord (12) which plugs into the electrical outlet

and a power-out cord (13) which plugs into the next charger.

To connect the chargers in a daisy chain:

X Plug the power-in cord (12) into an electrical outlet.

X Remove the power-in cord from the next charger and

plug in the power-out cord (13) rom the charger that is

now plugged into the outlet.

X Repeat this process for the remaining chargers.

Chargers that are daisy chained together operate

independently as though each one was plugged into a

separate outlet, therefore a battery can be removed from

anywhere along the daisy chain without affecting the other

chargers.

Use

Switching on and off (fig. D and E)

X To switch the tool on, press the variable speed trigger

switch (7).

X To switch the tool off, release the variable speed trigger

switch (7).

X A forward/reverse control button (4) determines the

direction of the tool and also serves as a lock off button.

X To select forward rotation, release the variable speed

trigger switch (7) and move the forward/reverse control

button (4) to the left, looking forward.

X To select reverse direction, move the forward/reverse

control button (4) in the opposite direction.

X The centre position of the control button (4) locks the

tool in the off position. Make sure that the variable speed

trigger switch (7) is released before changing the

position of the forward/reverse control button (4).

X If the tool does not turn on, check to see if one of the two

VPX™ battery packs is depleted. See the section

‘Battery LED indicators’ below.

Battery LED indicators

This product is equipped with electronics which will shut-off

the power when either battery pack is depleted. If the tool

stops suddenly, one of battery packs may be depleted. An

LED (14) on the back of the tool handle will indicate which

battery pack is depleted.

In order to illuminate the indicator (14) squeeze the variable

speed trigger switch (7). To insure optimal runtime, remove

both battery packs and place in a charger. Two battery

indicators are located on the back of the tool above the

batteries. If battery power is depleted while using your

appliance, you can determine which battery needs to be

recharged.

To check battery status:

X Squeeze the trigger and observe which LED is

illuminated.

X Remove the battery pack corresponding to the LED

which is illuminated.

Torque control (fig. D and E)

Your tool is fitted with a 24 position collar (2 or 8) to select

the operating mode and to set the torque for tightening

screws. Large screws and hard workpiece materials require

a higher torque setting than small screws and soft workpiece

materials.

X For drilling in wood, metal and plastics, set the collar to

the drilling position symbol.

X For screwdriving, set the collar to the desired setting. If

you do not know the appropriate setting, proceed as

follows:

X Set the collar to the lowest torque setting.

X Tighten the first screw.

X If the clutch ratchets before the desired result is

achieved, increase the collar setting and continue

tightening the screw. Repeat until you reach the correct

setting. Use this setting for the remaining screws.

Hammer action (VPX1222 only)

Your drill has hammer action:

X For drilling in masonry, set the torque control collar to

the position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker vpx 1212 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info