Bedienungsanleitung Black Decker vpx 1212 (Seite 8 von 97) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

388366

Zoom out

Zoom in

Vorherige Seite

1/97

Nächste Seite

ENGLISH

High/low speed selector (fig. D and E)

The 2-speed feature of your drill allows for greater versatility.

X To select the low speed, high torque setting (position 1),

turn the tool off and allow it to stop. Move the speed

selector switch (3) towards the back.

X To select the high speed, low torque setting (position 2),

turn the tool off and allow it to stop. Move the speed

selector switch (3) towards the front.

Warning! Do not move the speed selector button with the

tool switched on.

Keyless chuck (fig. E)

To insert a drill bit or other accessory:

X Hold the chuck (1) and rotate it in a counter clockwise

direction, as viewed from the chuck end.

X Insert the bit or other accessory fully into the chuck, and

tighten securely by rotating the chuck (1) in the

clockwise direction.

Warning! Do not attempt to tighten drill bits (or any other

accessory) by gripping the chuck and turning the tool on or

damage to the chuck and personal injury may occur.

Driving screws

X When driving screws, the forward/reverse button (4)

should be pushed to the left.

Move the forward/reverse button (4) pushed to the right for

removing screws.

Drilling

X Use sharp drill bits only.

X Support and secure the work properly.

X Run the drill very slowly, using light pressure, until the

hole is started.

X Apply pressure in a straight line with the bit. Use enough

pressure to keep the bit biting but not so much as to stall

the motor or deflect the bit.

X Hold the drill firmly with two hands to control its twisting

action.

X Do not click the trigger of a stalled drill on and off in an

attempt to start it. Damage to the drill can result.

X Minimize stalling on breakthrough by reducing pressure

and drilling slowly through the last part of the hole.

X Keep the motor running while pulling the bit out of a

drilled hole. This will help reduce jamming.

X With variable speed drills there is no need to centre

punch the point to be drilled. Use a slow speed to start

the hole and accelerate by squeezing the trigger harder

when the hole is deep enough to drill without the bit

skipping out. Operate at full speed after starting the bit.

Drilling wood

Holes in wood can be made with the same twist drill bits used

for metal or with spade bits. These bits should be sharp and

should be pulled out frequently when drilling to clear chips

from the flutes of the drill.

Drilling in metal

Use a cutting lubricant when drilling metals. The exceptions

are cast iron and brass which should be drilled dry. The

cutting lubricants that work best are sulfurized cutting oil or

lard oil.

Drilling in masonry (VPX1222 only)

Use carbide tipped masonry bits. Refer to the section

“Drilling”. Keep an even force on the drill but not so much that

you crack the brittle material. A smooth, even flow of dust

indicates the proper drilling rate.

Maintenance

Your Black & Decker tool has been designed to operate over

a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regular cleaning.

Your charger does not require any maintenance apart from

regular cleaning.

Warning! Before performing any maintenance on the tool,

remove the battery from the tool. Unplug the charger before

cleaning it.

X Regularly clean the ventilation slots in your tool and

charger using a soft brush or dry cloth.

X Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

X Regularly open the chuck and tap it to remove any dust

from the interior.

Protecting the environment

Separate collection. This product must not be

disposed of with normal household waste.

Should you find one day that your Black & Decker product

needs replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product

available for separate collection.

Separate collection of used products and packaging

allows materials to be recycled and used again. Re-

use of recycled materials helps prevent

environmental pollution and reduces the demand

for raw materials.

Local regulations may provide for separate collection of

electrical products from the household, at municipal waste

sites or by the retailer when you purchase a new product.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker vpx 1212 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info