Bedienungsanleitung Blaupunkt montana rdm 169 (Seite 15 von 30) (Englisch)

165716

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

ENGLISH

DEUTSCH

FRANÇAIS

ITALIANO

NEDERLANDS

SVENSKA

ESPAÑOL

PORTUGUÊS

• Tune into a station with the rocker

switch (either automatically or manual-

ly).

• Press the desired preset button until

the radio resumes play after the muting

(takes approximately 2 seconds) or un-

til you hear a beep.

Now the station has been stored.

The display will indicate which station has

been stored.

Note:

If you attempt to store a station which is al-

ready stored, the corresponding station and

the station preset will flash in the display if

you are in a different memory bank.

Storing stations with the stron-

gest reception automatically

with Travelstore

You can automatically store the six FM sta-

tions with the most powerful signals in your

current reception area sorted according to

their signal strength. This function is parti-

cularly convenient on longer trips.

•

Press the “BA/TS” button for 2 seconds.

“T-STORE” will appear in the display.

The six strongest FM stations will be auto-

matically stored on the memory bank “T”

(Travelstore). When this process has been

completed, the name of the strongest stati-

on will appear in the display and begin to

play.

If desired, stations can also be stored ma-

nually in the Travelstore bank, refer to the

section on “Storing stations”.

Recalling stored stations

You can recall any stored station at the touch

of a button.

• Select the waveband by pressing BA/

TS. For FM, also choose the corre-

sponding memory bank by pressing

the BA/TS button as many times as

necessary until the desired bank ap-

pears in the display.

• Press the corresponding preset button

briefly to recall the station.

Scanning stations with Radio

Scan

You can scan through all of the stations in

your reception area.

To start the Scan function:

• Press “SC” for approximately 2 secon-

ds.

The scanned frequency or the station name

will start flashing in the display.

During the scanning process “FM-SCAN” or

“AM-SCAN” will light up in the display.

If you want to continue listening to the stati-

on which is being scanned, then

• Press “SC” briefly.

This ends the Radio Scan function.

If no station is selected, the scan function

will switch off after the frequency band has

run through. The station selected previous-

ly will resume play.

Changing the scan time

The scan time per radio station can be set

to between 5 and 20 seconds.

For more detailed information, refer to the

section on “DSC programming - SCANTI-

ME”.

Selecting the automatic tuning

sensitivity

You can alter the automatic tuning sensiti-

vity.

If “lo” is displayed, the radio will only pick up

strong, local stations (low sensitivity).

If “lo” does not light up, the radio will also

pick up weaker, more distant stations.

To switch the automatic tuning sensitivity

and program the sensitivity level, refer to the

section on “DSC programming “.

BA AcaBiaMonSevRDM168/169gb® 28.05.2002, 15:48 Uhr43

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blaupunkt montana rdm 169 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Blaupunkt montana rdm 169

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info