714526
29
Zoom out
Zoom in
Vorherige Seite
1/48
Nächste Seite
EN
29
Installation
www.bora.com
Fasten the cooktop to the worktop using the mounting
brackets [8].
Next, insert the stainless steel grease filter [4] and the
air inlet nozzle [3].
Seal the surrounding gap with black, heat-resistant
silicone sealant.
6.8 Establishing the power connection
Observe all safety and warning information
(see the Safety chapter).
Observe all national and regional laws and regulations
as well as the supplementary regulations of the local
utility companies.
INFO The power connection may only be established
by certified specialists. He/she also assumes
responsibility for the proper installation and
commissioning.
INFO Connections via plug-in contacts (Schuko plugs)
are not permitted.
INFO The device complies with IEC 61000-3-12
Switch off the main switch/automatic circuit breaker
before connecting the cooktop.
Protect the main switch/automatic circuit breaker
from being switched on without permission.
Make sure the device is not energised.
Connect the cooktop exclusively via a fixed connection
to an H 05 VV-F power supply cable with corresponding
minimum cross-section (see tab. Fuse protection and
minimum cross-section).
Connection Fuse protection Minimum
crosssection
3-phase connection 3 x 16 A 2.5 mm
2
2-phase connection 2 x 16 A 2.5 mm
2
1-phase connection 1 x 32 A 4 mm
2
Tab. 6.2 Fuse protection and minimum cross-section
1
L1 L2 L3
2 3 4
N PE
220 - 240 V~
220 - 240 V~
220 - 240 V~
Fig. 6.36 Connection diagram 3-phase connection
For surface mounting
Make sure that the sealing tape is resting on the worktop.
For flush installation
Make sure that the sealing tape of the cooktop is
sealed well all the way round.
1
2
Fig. 6.34 Height adjustment plates
[1] Cooktop
[2] Height adjustment plate
If applicable, insert the height adjustment plate [2].
54321
8
5
7
6
1
Fig. 6.35 Connect the air duct + secure
[1] Cooktop
[2] Suction opening
[3] Air inlet nozzle
[4] Stainless steel grease filter
[5] Worktop cut-out
[6] Exhaust air arc
[7] Exhaust air duct
[8] Mounting bracket
Connect the exhaust air duct [7] at the installation site
to the exhaust air arc [6].
Seal the duct connection so that it is airtight using
adhesive sealing tape UDB1.
29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bora BFIAS wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Bora BFIAS

Bora BFIAS Bedienungsanleitung - Deutsch - 52 seiten

Bora BFIAS Bedienungsanleitung - Holländisch - 52 seiten

Bora BFIAS Bedienungsanleitung - Französisch - 52 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info