Bedienungsanleitung Bora BFIAS (Seite 30 von 48) (Englisch)

714526

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Installation

www.bora.com

6.9 Device power management

(overall power reduction)

INFO

The device power management function can be set

in the service menu. Accessing the service menu and

changing the power management setting may only be

performed by a certified specialist.

The total device power can be reduced to 4.4 kW upon

initial commissioning if the required electrical power

cannot be provided at the installation site.

The connection must always be equipped with 20 A fuse

protection as a minimum.

Programming the device power management

Prerequisites:



The cooktop is switched off.



All cooking zones are switched off.

 Separate the device from the voltage supply using the LS

switch, fuses, automatic circuit breakers or contactors.



After re-establishing the voltage supply, you have up to

two minutes to open the service menu.

 Re-connect the appliance to the voltage supply.

 Press and hold the multi-function button.

 Briefly press the timer button.



A short signal tone will sound and the front half of the

setting ring lights up.

 Now release the multi-function button.

 Swipe the setting ring in a circular, clockwise motion

to move from 3 to 8.

Fig. 6.40 Opening the service menu



is displayed intermittently with

and

on the left

front cooking zone indicator.



is displayed in the left back cooking zone indicator

(factory setting).

 Use the multi-function button to select the menu level

 Press any key at the adjusting ring to change the

setting of the back left cooking zone from

 Press the timer button to save the change.



The cooktop is ready for use.

L1 L3

2 3 4

N PE

220 - 240 V~

Fig. 6.37 Connection diagram 2-phase connection

2 3 4

N PE

220 - 240 V~

Fig. 6.38 Connection diagram 1-phase connection

Fig. 6.39 Electrical connections of the cooktop

[1] Bore holes

[2] Power supply

[3] Connection control

[4] Cable mounting clip

 Connect the power supply cable to the power supply [2]

of the cooktop with cooktopFig. 6.36r in accordance

with the relevant connection diagram (see fig. 6.36

Connection diagram).

 For a 1-phase or 2-phase connection, connect the

relevant contacts with the BKAS connector clip

(in scope of delivery).

 Fasten the cable mounting clips [3] to the designated

bore holes [1] either on the left or right hand side for

the cable routing to the rear.

 Ensure that the cable is not caught or damaged and is

not able to touch any hot hobs.

 Verify that the installation was done correctly.

 Switch on the main switch/automatic circuit breaker.

 Put the cooktop into operation (see the Operation

chapter).

 Check all the functions are working correctly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bora BFIAS Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bora BFIAS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info