Bedienungsanleitung Bora PL540E (Seite 20 von 36) (Englisch)

714384

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Installation

www.bora.com

 The exhaust air must be directed outside or to the

recirculation unit through appropriate ducts.

 For further planning examples and notices, please see

the ventilation handbook (not included in the scope of

delivery).

Installing the additional fan

 Install the additional fan in the exhaust duct.

 Ensure that a minimum clearance of 300 cm is

maintained between the fan units.

 Only use BORA universal fans with your BORA cooktop

extractor system.

Operating the cooktop extractor with a

fireplace that depends on the air in the room

INFO The state and regional laws and regulations

must be observed with regard to the exhaust

duct design. A sufficient air supply must be

ensured.

Fireplaces that depend on the air in the room (e.g. gas,

oil, wood or coal-fired heaters, continuous-flow water

heaters, instantaneous water heaters) draw in air from

the room in which they are installed and release the

exhaust fumes into the outside air via an exhaust system

(e.g. chimney).

If the cooktop extractor is used in exhaust mode, it draws

in air from the room in which it is installed as well as from

neighbouring rooms. If there is insufficient air supply, low

pressure will occur. Toxic gases could be drawn out of the

chimney or extraction ducting and back into the room.

Fig. 6.24 Exhaust air installation – not permitted

Fig. 6.25 Exhaust air installation – correct

6.5.4 Installation – standard set-up

Fig. 6.23 Standard set-up

[1] Cooktop extractor

[2] 90° diverter

[3] Horizontal tube bend

[4] Silencer

[5] Universal plinth fan

[6] Air duct/recirculation unit

[7] Universal control unit

 Push the tube bend [3] onto the exhaust fitting of the

cooktop extractor [1].

 Push the 90° diverter [2] onto the tube bend [3].

 Position the plinth fan [5].

 To facilitate positioning, the inlet nozzle on the plinth

fan can be removed. To do this, please see the assembly

instructions for the ULS25 universal plinth fan.

 Connect the silencer [4] to the plinth fan [5].

 Connect the silencer [4] to the 90° diverter [2].

 Use the UDB25 sealing tape (not included in the scope

of delivery) to adhere together the connections for the

ducting sections with an air tight join.

 You can also optimally adhere together the connections

between the ducting sections and the plinth fan with

UDB25 sealing tape.

INFO Position the plinth fan and the universal

control unit in such a way that they are easily

accessible and removable for maintenance

work.

 The maximum exhaust air duct length with a fan is 6 m.

 The minimum cross-section of the air ducts must

be 176 cm

, which equates to a round pipe with a

diameter of 150 mm.

 For the ducting, only use stable duct elements with

smooth pipe interiors. Do not use flexible or fabric

tubes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bora PL540E Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bora PL540E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info