Bedienungsanleitung Bora PL540E (Seite 21 von 36) (Englisch)

714384

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Installation

www.bora.com

Fig. 6.27 Control box connections

[1] CAT 5 communication cable connection

[2] Cover flap connection cable

 Connect the CAT 5 communication cable between the

control box connection [1] and the universal control

unit [1].

 Connect the cable for the cover flap sensor to the

control box [2].

Fig. 6.28 Connection plug of the plinth fan

[1] Connection plug of the plinth fan control line

[2] Connection plug of the plinth fan power supply cable

 Connect the plinth fan’s control line [1] to the

universal control unit [4].

 Connect the plinth fan’s power supply cable [2] to the

universal control unit [6].

Release the power supply cable

To release the power supply cable [2] from the universal

control unit [6] you need a small flathead screwdriver.

 Disconnect the universal control unit’s power supply

cable from the power supply [8].

 Make sure that there is no power to the appliance.

 Use the flathead screwdriver to loosen the lock on the

power supply cable’s plug.

 To do this, insert the flathead screwdriver into the gap

in the socket.

 Press the lock down gently.

 Use the flathead screwdriver to gently lever the plug

of the power supply cable out of the universal control

unit’s socket.

 Now disconnect the power supply cable from the

socket.

 Check the plug and the socket for damage.

 Do not use damaged components.

 If simultaneously operating both a fireplace and the

cooktop extractor in the same room, ensure that:

 the maximum low pressure is 4 Pa (4 x 10–5 bar);

 a safety device (e.g. window contact switch, low

pressure warning device) is used to ensure that a

sufficient supply of fresh air is guaranteed;

 the exhaust air is not be ducted into a chimney that

is used for exhaust gases of devices operated with

gas or other combustibles;

 the installation is checked and approved by an

authorised certified engineer (e.g. heating engineer).

6.6 Establishing the power

connection and communication

 Observe all safety and warning information

(see the Safety section).

 Observe all national and regional laws and regulations

as well as the supplementary regulations of the local

utility companies.

 The plug for the power supply must be accessible

following installation.

 If the power supply cable has been damaged this must

be replaced.

Connecting the universal control unit and fan

to the cooktop extractor control box

Fig. 6.26 Connections on the universal control unit

[1] CAT 5 communication cable

[2] Home-Out

[3] Home-In

[4] Fan 1 control line

[5] Fan 2 control line

[6] Fan 1 power supply cable

[7] Fan 2 power supply cable

[8] Power supply cable with microfuse

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bora PL540E Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bora PL540E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info