Bedienungsanleitung Boretti BIKW 75 (Seite 55 von 60) (Englisch, Holländisch, Französisch, Spanisch)

77368

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Installation instructions

The installation comes under the exclusive res-

ponsibility of specialists. The installer is held

to respect the legislation and the standards

enforce in his home country.

How to stick the gasket:

The gasket supplied with the hob avoids all inﬁl-

tration of liquids in the cabinet.

His installation has to be done carelessly, in

conformity of the following drawing. Stick the gasket (2) two millimeters from the

external edge of the glass, after removing the

protection sheet (3).

2 mm

Fitting - installing:

The cut-out sizes for the hobs are:

• The piece of furniture or the support in which

the hob is to be ﬁtted, as well as the edges

of furniture, the laminate coatings and the

glue used to ﬁx them, must be able to resist

temperatures of up to 100 °C.

• The mural rods of edge must be heat-resi

sting.

• The hobs are classiﬁed as “Y” class for heat

protection. Ideally the hob should be instal-

led with plenty of space on either side. There

may be a wall at the rear and tall units or a

wall at one side. On the other side, however,

no unit or divider must stand higher than the

hob.

• Ensure that there is a distance of 50 mm

between the hob and the wall or sides.

• Materials which are often used to make work

tops expand on contact with water. To pro-

tect the cut out edge, apply a coat of varnish

or special sealant. Particular care must be

given to applying the adhesive joint supplied

with the hob to prevent any leakage into the

supporting furniture. This gasket guaranties

a correct seal when used in conjunction with

smooth work top surfaces.

• Not to install the hob to the top of a not ven

tilated oven or a dishwasher.

• To guarantee under the bottom of the hob

casing a space of 20 mm to ensure a good air

circulation of the electronic device.

• To guarantee between the work top and the

top of the drawer or oven a space of 5 mm to

allow the exit of the air ﬂow.

• If a drawer is placed under the work, avoid

to put into this drawer ﬂammable objects

(for example : sprays) or not heat-resistant

objects.

• The safety gap between the hob and the

cooker hood placed above must respect the

indications of the hood manufacturer. In case

of absence of instructions respect a distance

minimum of 760 mm.

• The connection cord should be subjected, af

ter builting, with no mechanical constraint,

such for example of the fact of the drawer.

• The installation of the hob in non stationary

sites ( for example : boat ) should be under-

taken by specialists.

Appliance Worktop Cut-out (mm) Glass Cut-out (if “ﬂushline” integration)

Width x Depth W D T radius

BBIK-70 660 x 490 702 512 5 11

BIKW-75 765 x 495 786 516 5 11

Downloaded from www.vandenborre.be

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Boretti BIKW 75 Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Boretti BIKW 75

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info