Bedienungsanleitung Boretti BIKW 75 (Seite 56 von 60) (Englisch, Holländisch, Französisch, Spanisch)

77368

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Electrical connection

• The installation of this appliance and the connection to the electrical network should be entrus-

ted only to an electrician perfectly to the fact of the normative regulations and which respects

them scrupulously.

• Protection against the parts under tension must be ensured after the builting-in.

• The data of connection necessary are on the stickers place on the hob casing near the con

nection box.

• The connection to the main must be made using an earthed plug or via an omnipolar circuit

breaking device with a contact opening of at least 3 mm.

• The electrical circuit must be separated from the network by adapted devices, for example :

circuit breakers, fuses or contactors.

Caution !

This appliance has only to be connected to a network 230 V~ 50 Hz. Connect always the earth

wire. Respect the connection diagram. The connection box is located underneath at the back of

the hob casing. To open the cover use a medium screwdriver. Place it in the slits and open the

cover.

(*) calculated with the simultaneous factor following standard TN 60 335-2-6/1990.

Connecting the cooktop:

For the various connections use the brass bridges which are in the terminal box.

1 phase 23 0V~1F+N (not for the Netherlands!):

Place a bridge between 1 and 2 then between 4 and 5. Attach the earthing to the “earth” terminal

clamp, the neutral N to terminal clamp 4 or 5, and phase L to terminal clamp 1 or 2.

2 phases 400V~2F+N:

Place a bridge between 4 and 5. Attach the earthing to the “earth” terminal clamp, the neutral N

to terminal clamp 4 or 5, phase L1 to terminal clamp 1 and phase L2 to terminal clamp 2.

2 phases 23 0V~2F+2N:

Place a bridge between 2 and 3. Connect the earthing to the “earth” terminal clamp, neutral N1 to

terminal clamp 4, neutral N2 to terminal clamp 5, phase L1 to clamp 1 and phase L2 to clamp 2.

Caution ! ensure that you : correctly attach the wires and the bridges. Tighten the screws properly.

Before making the connection, we strongly advise you to locate the phase(s), neutral and earth on

the mains. If you have any doubts, call your electrician. Note: the bridges between terminals 4-5

and between terminals 1-2 were installed during the factory check. We cannot be held responsible

for any incident resulting from incorrect connection or which could arise from the use of an ap-

pliance which has not been earthed or has been equipped with a faulty earth connection.

Mains Connection Cable diameter Protection calibre

230V~1P+N 50Hz 1 Phase + N 3 x 2.5 mm² 25 A *

400V~2P+N 50Hz 2 Phases + N 4 x 1.5 mm² 16 A *

230V~2P+2N 50 Hz 2 Phases + 2N 5 x 1,5 mm² 16 A *

Downloaded from www.vandenborre.be

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Boretti BIKW 75 Seite 56

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Boretti BIKW 75

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info