Bedienungsanleitung Bosch 0 607 452 604 (Seite 18 von 126) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

97286

Zoom out

Zoom in

Vorherige Seite

1/126

Nächste Seite

18 | English 3 609 929 A78 • 8.8.06

Exhaust Line

Slip the exhaust hose (combined) 13, which carries the

exhaust air away from your workplace, over the air inlet

hose 14. Then connect the pneumatic tool to the air

supply (see “Connection to the Air Supply”, page 18)

and pull the exhaust hose (combined) 13 over the

mounted air inlet hose to the end of the tool.

Connection to the Air Supply

The pneumatic tool is designed for an operating pres-

sure of 6.3 bar (91 psi). For maximum performance, the

inner diameter of the hose is 10 mm with connection

threads of G 1/4". To maintain full performance, use

only hoses with a maximum length of 4 m.

The supplied air must be free of foreign material and

moisture to protect the pneumatic tool from damage,

contamination, and rust.

Note: The use of a compressed air maintenance unit is

necessary. This ensures optimum functioning of com-

pressed air tools.

Observe the operating instructions of the maintenance

unit.

All fittings, connecting lines, and hoses must be dimen-

sioned for the required air pressure and volume.

Avoid restrictions in the air supply resulting from, e.g.,

pinching, kinking, or stretching!

In case of doubt, measure the pressure with a pressure

gauge at the air inlet with the pneumatic tool switched

on.

Connection of the Air Supply to the

Pneumatic Tool

Screw the hose nipple 8 into the connector at the air

inlet 7.

To prevent damage to the internal valve components of

the tool, you should use an open-end spanner (size

22 mm) to apply a counterforce at the protruding con-

nector of the air inlet 7 when screwing/unscrewing the

hose nipple 8.

Loosen the hose clamps 15 of the air inlet hose 14 and

attach the air inlet hose over the hose nipple 8 by firmly

tightening the hose clamp.

Note: Always connect the air inlet hose first to the

pneumatic tool, then to the maintenance unit.

Slip the air inlet hose 14 over the coupling nipple 16

and attach the air inlet hose by firmly tightening the

hose clamp 15.

Screw a quick hose connector 17 in the air outlet of the

maintenance unit 18. Quick hose connectors make

possible a quick connection and, when uncoupled,

thea shut off the air supply automatically.

Take care that you do not start the pneumatic tool acci-

dentally when you insert the coupling nipple 16 into the

coupler 17.

Changing the Tool

f When you install the tool bit, take care that

the tool bit is seated securely on the tool bit

holder. If the tool bit is not joined securely to the

tool bit holder, it may become loose and it may no

longer be controllable.

The angle nutrunners with shut-off mechanism are

delivered with an angled drive head (3/8" square drive),

but without tool bits.

OBJ_BUCH-220-001.book Page 18 Tuesday, August 8, 2006 9:41 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch 0 607 452 604 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info