Bedienungsanleitung Bosch 3600 HA2 - Indego 1000 Connect (Seite 37 von 456) (Alle Sprachen)

606589

Zoom out

Zoom in

Vorherige Seite

1/456

Nächste Seite

English | 37

Bosch Power Tools F 016 L81 517 | (27.10.15)

EN 301 489-7 V1.3.1 (EMC and ERM for GSM and DCS),

EN 301 511 V9.0.2 (GSM 900 and GSM 1800 Bands Essen-

tial Requirements), EN 55014-1:2006+A2:2011 (EMC

Emissions),EN 55014-2:1997+A2:2008 (EMC Immunity).

Guaranteed sound power level 75 dB(A).

Conformity assessment procedure according to Annex VI.

Equipment category: 32

Notified body for 2000/14/EC:

SRL, Sudbury, England, Nr. 1088

Technical file (2006/42/EC, 2000/14/EC) at:

Bosch Lawn and Garden Ltd., PT-HG/ENS-PA2,

Stowmarket, Suffolk IP14 1EY, England

Robert Bosch GmbH, Power Tools Division

70764 Leinfelden-Echterdingen, GERMANY

Leinfelden, 27.10.2015

Explanation of Installation Guide

(seepages3–14)

Lawn Preparation

Remove stones, loose pieces of wood, wire, live mains cables

and other foreign objects from the cutting area.

Make sure that the cutting area is even and has no ditches,

grooves and steep slopes above 20° that are clear obstruc-

tions for the machine.

Cut the main area of the lawn with a conventional mower to a

max. height of 40 mm and the perimeter wire area to a max.

height of 20 mm.

Installation

For a video guide on how to install the Indego please visit

www.bosch-indego.com or use the following QR-Code.

Select a position for the docking station, horizontally levelled

and out of direct sunlight.

Note: The docking station must be positioned on the wire at

an outer edge of the cutting area. It cannot be positioned by

the side of a shed or workshop that appears as an island with-

in the cutting area.

Make sure that the docking station is placed beside the cut-

ting area with a straight 1.5 m track in front of the docking sta-

tion and a straight 1 m track behind. Whilst stood in the grass

area to be cut it is important that the docking station charging

pins point to the left. (see figure 2)

Note: If the docking station is positioned with the charging

pins pointing either into the grass area or pointing to the right

the Indego will not run correctly.

Pull the wire end through the front hole of the base plate and

straight through the wire duct and the rear hole. Fix the wire

with a peg inline with the hole. Cut off insulation carefully and

connect the wire to the right hand (red) terminal. (see

figures 5– 6)

Fix the docking station with 4 supplied fixing pins to the

ground. (see figure 7)

Lay out the perimeter wire anti-clockwise and flush to the

ground. Observe the minimum distances from lawn edges,

steps, walls, ponds, etc. Use the spacing guide. (see figure 8)

Note: The cable should be positioned so that the Indego will

not be more than 16 m away at anytime.

If the working area borders against a flat path or surface that

is level with the lawn the Indego will be able to run over it. In

such cases the perimeter wire should be positioned right up

to the edge of the lawn.

Note: Perimeter wire can be buried up

to a maximum depth of 5 cm. It is recommended to mark out

permanent objects within the garden. This will prevent the In-

dego colliding with the object and reduce wear on the shell.

Objects on the lawn below 6 cm height e.g. trees, ponds, flow-

er beds etc. must be delimited in a clockwise direction. The

Henk Becker

Executive Vice President

Engineering

Helmut Heinzelmann

Head of Product Certification

PT/ETM9

Action Figure Page

Delivery scope/unpacking product

1 4

Position the docking station

2–4 4–6

Thread wire through base plate

5 6

Connect first end of perimeter wire

6 6

Fix docking station to the ground

7 6

Lay out perimeter wire

8 7

Extend perimeter wire

9 8

Lay out additional area with perimeter

wire 10 8

Connect second end of perimeter wire

11 9

Clip on protective cover of docking

station

12 9

Install power supply

13 10

Docking station indicates power on

14 10

Plug in isolator key

15 10

Charge battery by putting the machine

into docking station

16 11

Welcome screen = Refer to manual

17 11

Lift up and carry the machine

18 12

Set height of cut

19 12

Logicut Intelligent Cutting

20 13

Cleaning

A 14

Maintenance

B 14

OBJ_BUCH-1573-008.book Page 37 Tuesday, October 27, 2015 10:35 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch 3600 HA2 - Indego 1000 Connect Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch 3600 HA2 - Indego 1000 Connect

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info