Bedienungsanleitung Bosch AdvancedGrind 18 (Seite 20 von 293) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

707739

Zoom out

Zoom in

Vorherige Seite

1/293

Nächste Seite

20 | English

1 609 92A 47W | (24.11.17) Bosch Power Tools

The vibration level given in this information sheet has been

measured in accordance with a standardised test given in

EN 60745 and may be used to compare one tool with anoth-

er. It may be used for a preliminary assessment of exposure.

The declared vibration emission level represents the main ap-

plications of the tool. However if the tool is used for different

applications, with different accessories or insertion tools or is

poorly maintained, the vibration emission may differ. This

may significantly increase the exposure level over the total

working period.

An estimation of the level of exposure to vibration should also

take into account the times when the tool is switched off or

when it is running but not actually doing the job. This may sig-

nificantly reduce the exposure level over the total working

period.

Identify additional safety measures to protect the operator

from the effects of vibration such as: maintain the tool and the

accessories, keep the hands warm, organisation of work pat-

terns.

Assembly

Battery Charging

 Use only the chargers listed in the technical data. Only

these chargers are matched to the lithium-ion battery of

your power tool.

Note: The battery supplied is partially charged. To ensure full

capacity of the battery, completely charge the battery in the

battery charger before using your power tool for the first time.

The lithium-ion battery can be charged at any time without re-

ducing its service life. Interrupting the charging procedure

does not damage the battery.

The lithium-ion battery is protected against deep discharging

by the “Electronic Cell Protection (ECP)”. When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

 Do not continue to press the On/Off switch after the

machine has been automatically switched off. The bat-

tery can be damaged.

Observe the notes for disposal.

Removing the battery

To remove the battery 5, press the battery unlocking button 6

and pull the battery upward out of the power tool. Do not ex-

ert any force.

Battery Status Indicator (4)

The charge-control indicator displays the charge condition of

the battery for several seconds when the On/Off switch is

half-pressed or fully pressed; it consists of 3 green LEDs.

The 3 LEDs in the charge-control indicator flash quickly

when the temperature of the battery is outside of the op-

erating temperature range of –30 to +65 °C and/or the

overload protection has been triggered.

Mounting the Protective Devices

 Before any work on the machine itself (e. g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

the On/Off switch.

 Note: After breakage of the grinding disc during operation or

damage to the holding fixtures on the protection guard/pow-

er tool, the machine must promptly be sent to an after-sales

service agent for maintenance. For addresses, see section

“After-sales Service and Application Service”.

Protection Guard for Grinding

Fitting the protective guard:

Turn the black plastic ring (see Figure B) until the groove 24

on the ring meets the slot for the nose on the clamping lever 1.

Place the protective guard 11 with the four noses in the four

grooves on the bearing seat (see Figures B and C).

Press the protective guard 11 downwards and turn it clock-

wise into the required working position (see Figure D). The

clamping lever 1 automatically clamps the protective guard

securely in this working position.

Adjusting the protective guard:

Turn the protective guard 11 in the clockwise direction only

into the required working position. The clamping lever 1 auto-

matically clamps the protective guard securely in this working

position.

 Adjust the protection guard 11 in such a manner that

sparking is prevented in the direction of the operator.

Note: The encoding keys on the protection guard 11 ensure

that only a protection guard that fits the machine type can be

mounted.

Removing the protective guard:

Turn the protective guard 11 so that the four noses engage in

the four grooves on the bearing seat (see Figure B) and re-

move the protective guard.

LED Capacity

Continuous lighting 3 x green ≥66 %

Continuous lighting 2 x green 33–66 %

Continuous lighting 1 x green 11–33 %

Slow flashing 1 x green ≤10 %

OBJ_BUCH-2850-004.book Page 20 Friday, November 24, 2017 11:44 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch AdvancedGrind 18 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info