Bedienungsanleitung Bosch AdvancedGrind 18 (Seite 23 von 293) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

707739

Zoom out

Zoom in

Vorherige Seite

1/293

Nächste Seite

English | 23

Bosch Power Tools 1 609 92A 47W | (24.11.17)

Working Advice

 Exercise caution when cutting slots in structural walls;

see Section “Information on Structures”.

 Clamp the workpiece if it does not remain stationary

due to its own weight.

 Do not strain the machine so heavily that it comes to a

standstill.

 After heavily straining the power tool, continue to run

it at no-load for several minutes to cool down the acces-

sory.

 Do not touch grinding and cutting discs before they

have cooled down. The discs can become very hot while

working.

 Do not use the power tool with a cut-off stand.

Rough Grinding

 Never use a cutting disc for roughing.

The best roughing results are achieved when setting the ma-

chine at an angle of 30° to 40°. Move the machine back and

forth with moderate pressure. In this manner, the workpiece

will not become too hot, does not discolour and no grooves

are formed.

Flap Disc

With the flap disc (accessory), curved surfaces and profiles

can be worked.

Flap discs have a considerably higher service life, lower noise

levels and lower sanding temperatures than conventional

sanding sheets.

Cutting Metal

 For cutting with bonded abrasives, always use the pro-

tection guard for cutting 12.

When cutting, work with moderate feed, adapted to the mate-

rial being cut. Do not exert pressure onto the cutting disc, tilt

or oscillate the machine.

Do not reduce the speed of running down cutting discs by

applying sideward pressure.

The machine must

always work in an up-

grinding motion. Other-

wise, the danger exists

of it being pushed

uncontrolled out of the

cut.

When cutting profiles

and square bar, it is best

to start at the smallest

cross section.

Cutting hard materials

 Wear a suitable dust mask, e.g. P2 Standard.

 The machine may be used only for dry cutting/grinding.

For cutting especially hard material, e.g., concrete with high

pebble content, the diamond cutting disc can overheat and

become damaged as a result. This is clearly indicated by cir-

cular sparking, rotating with the diamond cutting disc.

In this case, interrupt the cutting process and allow the dia-

mond cutting disc to cool by running the machine for a short

time at maximum speed with no load.

Noticeably decreasing work progress and circular sparking

are indications of a diamond cutting disc that has become

dull. Briefly cutting into abrasive material (e.g. lime-sand

brick) can resharpen the disc again.

Information on Structures

Slots in structural walls are subject to the Standard DIN 1053

Part 1, or country-specific regulations.

These regulations are to be observed under all circumstanc-

es. Before beginning work, consult the responsible structural

engineer, architect or the construction supervisor.

Recommendations for Optimal Handling of the Battery

Protect the battery against moisture and water.

Store the battery only within a temperature range between

–20 °C and 50 ° C. As an example, do not leave the battery in

the car in summer.

Occasionally clean the venting slots of the battery using a soft,

clean and dry brush.

A significantly reduced working period after charging indi-

cates that the battery is used and must be replaced.

Observe the notes for disposal.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself (e.g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

the On/Off switch.

 For safe and proper working, always keep the machine

and ventilation slots clean.

 Please store and handle the accessory(-ies) carefully.

After-sales Service and Application Service

Our after-sales service responds to your questions concern-

ing maintenance and repair of your product as well as spare

parts. Exploded views and information on spare parts can

also be found under:

www.bosch-pt.com

Bosch’s application service team will gladly answer questions

concerning our products and their accessories.

In all correspondence and spare parts orders, please always

include the 10-digit article number given on the nameplate of

the product.

OBJ_BUCH-2850-004.book Page 23 Friday, November 24, 2017 11:44 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch AdvancedGrind 18 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info