Bedienungsanleitung Bosch AMAX 4000 (Seite 36 von 158) (Englisch)

697457

Zoom out

Zoom in

Vorherige Seite

1/158

Nächste Seite

Contact your central monitoring station for the correct setting.

Network Polling Time

The polling is used for both panel and remote receiver to know whether the network

connection is good or not. Each time when a polling is due, the AMAX panel will send a polling

message. The polling time range is from 1 to 999 minutes. For time less than 3 digits, use 0 to

fulfill.

Contact your central monitoring station for the correct setting.

Reports

System Reporting

Report Transmission Sequence

If the event has disabled the report (option 0), no report is sent out. If the report has any

destination to contact the panel (option 1, 2, 3, 4, 5, 6, 7), It will call the related destination

by related reporting format type and subscriber ID Number.

Attempt rules:

1. Attempt times and duration

– Within the report expiring time the AMAX panel will retry sending the report to each

enabled destination till the report has been sent to the destination, or till the report

buffer overflows and the old report is replaced by new incoming reports.

– For each enabled destination, the retry interval time between two retries is 15

seconds for the 1st retry to 4th retry, and the retry interval time between two retries

is 10 minutes for the 5th retry to 8th retry, after the 8th retry the retry interval time

between two retries is 60 minutes.

2. Attempt Priority

– The attempt priority is destination 1, 2, 3, 4 Domestic. The disabled destinations will

be ignored.

3. Communication Fail Fault

– If the attempt times for one destination reaches 4, the system will cause the

communication fail fault for this destination.

4. Backup Destination Process

– The AMAX panel can save up to a maximum of 50 un-reported events. If the un-

reported events are more than 50, it will delete earlier event and only save the last

50 events in the buffer to send out.

Sequential Logic to Send Report

– If the event reporting path is set to 0, the relevant reports will not be sent

– If the event reporting path is set to a single path (receiver 1, 2, 3, or 4), the AMAX panel

will send reports to corresponding paths

– If the event reporting path is set to all paths (receiver 1, 2, 3, 4) and any one of these

paths fails, the communication path will fail

– If the event reporting path is set to sending report to receiver 1, with receiver 2, 3, 4 as

backup, the AMAX panel will send report to receiver 1 first. Only if send report to receiver

1 fails,the AMAX panel attempts to send report to 2, 3 and 4 in succession.

Communication path fault will occur when all valid paths fail. Communication path fault

will recover when any one of the paths recovers

Display of faults

When multiple reports are queued for delivery, the communication path fault is displayed as a

logic or relationship. Example:

7.1.2

36 en | Settings AMAX 2100 / 3000 / 4000

2013.10 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitsysteme GmbH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch AMAX 4000 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch AMAX 4000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info