Bedienungsanleitung Bosch AMAX 4000 (Seite 37 von 158) (Englisch)

697457

Zoom out

Zoom in

Vorherige Seite

1/158

Nächste Seite

Set zone status recovery report to send report to receiver 1. Set keypad emergency report to

send report to receiver 1, with receiver 2, 3, and 4 as backup.

Communication path fault is as follows: When communication paths 1, 2, 3, and 4 all fail, only

the illumination of zone indicator 1 expresses that communication path 1 of the zone status

recovery report fails and the all communication paths 1, 2, 3 and 4 of the keypad emergency

report fail as well.

Communication path fault recovery is as follows:

– When communication path 1 fault recovers, zone indicator 1 goes off, indicating that the

communication path 1 fault of the zone status recovery report recovers and the

communication part 1 fault of the keypad emergency report recovers

– When any one path fault of communication paths 2, 3, and 4 recover, as the

communication path fault is displayed as a logic or relationship, zone indicator 1 still

illuminates, indicating that the communication path 1 fault of the zone status recovery

report has not be recovered, but the path fault of the keypad emergency report has been

recovered

Zone Status Reporting and Zone Recovery Reporting

Alarm Report

In arming status, in case of alarm event, the alarm report will be sent.

Alarm Recovery Report

In arming status, when the zone recovers, the zone recovery report will be sent at the end of

alarm output time.

If the non-24-hour zone is not recovered in disarming, the system will automatically send a

zone recovery report. The 24 - hour zone sends the recovery report only when the zone

recovers.

Zone Fault Report

If the zone is triggered at the end of exit delay, a zone fault report will be sent, indicating that

the zone is automatically bypassed by the system. At the end of exit delay time, the 24-hour

zone in triggering status will not send the fault report, i.e., the 24-hour zone will not be

automatically bypassed.

The non 24-hour zone fault recovery report will be sent when the zone recovers or the system

disarms. For the 24-hour zone, only the alarm recovery event will occur.

The zone fault occurs when the zone is triggered and recovers when the zone is normal. Zone

fault will occur when one of the following conditions is met:

– For 24-hour zone, (internal) instant zone, if the forced arming option is set to allow, the

zone fault event will occur when the arming operation is executed while the zone is in

triggering status

– When the zone is locked

– For (internal) delay and (internal) follow zone, if they are still in triggering status at the

end of exit delay, zone fault event will occur

– For 24-hour zone, if it is in triggering status when the bypass is cancelled, zone fault

event will occur

Fault recovery conditions:

– Zone resumes to normal conditions

– When the failed (internal) delay zone, (internal) instant zone and (internal) follow zone

are disarmed, the fault recovery event will occur even if the zone is still in triggering

status

AMAX 2100 / 3000 / 4000

Settings | en 37

Bosch Sicherheitsysteme GmbH Installation Guide 2013.10 | 01 | F.01U.267.112

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch AMAX 4000 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch AMAX 4000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info