Bedienungsanleitung Bosch AMAX 4000 (Seite 39 von 158) (Englisch)

697457

Zoom out

Zoom in

Vorherige Seite

1/158

Nächste Seite

– Zone Expansion Module Tamper: When tamper occurs in the zone expansion module, the

tamper report will be sent. After the tamper recovers, a tamper recovery report will be

sent

– Keypad Tamper: When tamper occurs in any keypads, the tamper report will be sent.

After the tamper recovers, a tamper recovery report will be sent

Auxiliary Power Fault Report

When the system detects auxiliary power fault, the report will be sent.

Auxiliary Power Fault Restore Report

When the system detects auxiliary power fault recovery, the report will be sent.

AC Power Fault Report

When the system detects disconnection of AC power, the report will be sent.

AC Power Fault Recovery Report

When the system detects recovery of AC power, the report will be sent.

Battery Low Voltage Fault Report

When the battery voltage is lower than 11.0V or battery low voltage is detected in the dynamic

battery test, the AMAX panel will send the battery low voltage report.

The system continuously monitors the battery voltage and will perform a dynamic battery test

each time the system is armed, when the system is reset, or every 4 hours.

Battery Low Voltage Fault Recovery Report

When the battery voltage is lower than 12.0V or recovery to normal voltage is detected in the

dynamic battery test, the battery low voltage fault recovery report will be sent.

Times of Wrong Code Entry Exceeding Limit

When the times of entering wrong code reaches a specific value, an access denial report will

be generated and alarm will be made.

This function is used to prevent unwanted users from accessing the system. When the times of

entering wrong password reaches a specific value, the AMAX panel will execute following

actions:

– Activate alarm siren and other alarm outputs

– Lock all keypads for 3 minutes

– Send an access denial report

On-board Output 1 – 2 Fault

When on-board output 1 or 2 fails, the report will be sent. When the on-board output resumes

to normal conditions, the programmable output fault recovery report will be sent.

Communication Path 1 - 4 Fault

When any communication path fails, the report will be sent. When communication resumes to

normal conditions, the communication fault recovery report will be sent.

Changing Programming Parameters

When the programming parameters are changed and take effect, the report will be sent.

Keypad Emergency Alarm Reporting

If you press and hold both 1 and 3 for 3 seconds, or press and hold both [#] and [*] for 3

seconds, the emergency alarm report will be sent.

The emergency alarm report has no corresponding alarm recovery report.

Keypad Fire Alarm Reporting

If you press and hold both 4 and 6 for 3 seconds, the fire alarm report will be sent.

The fire alarm report has no corresponding alarm recovery report.

AMAX 2100 / 3000 / 4000

Settings | en 39

Bosch Sicherheitsysteme GmbH Installation Guide 2013.10 | 01 | F.01U.267.112

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch AMAX 4000 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch AMAX 4000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info