697457
40
Zoom out
Zoom in
Vorherige Seite
1/158
Nächste Seite
Keypad Medical Aid Reporting
If you press and hold both 7 and 9 for 3 seconds, the medical aid alarm report will be sent.
The medical aid alarm report has no corresponding alarm recovery report.
Automatic Test Reporting
The system supports sending automatic test report.
For more information about test report time programming, see Test Report Time. For more
information about date and time settings, see Date and Time Settings.
Report Expiry Time
If the report expiry time expires and the report path has not been connected to, the report will
be lost and not be sent. It can be maintained for 1 to 255 minutes. The system is defaulted to
000, indicating that the report has been tried to send without limit in expiry time.
Report Delay Entry Time
When the alarm occurs during entry time, then the AMAX panel sends report immediately or
delayed (30 sec.).
Automatic Test Report
The test report is divided into two types: periodic and regular daily report.
When the addresses 0129 - 0130 are programmed in 1 - 99, the system will send periodic
automatic test report at every hour specified by the address. If 0129 - 0130 are
programmed to 0, no periodic test reports will be sent.
When 0131 - 0134 is set to valid time, the system will send automatic test report at the
same time every day. At this moment, the date and time of the system must be correctly
set. If 0131 - 0134 is set to be invalid time, the daily regular automatic test report will be
disabled.
Dual IP
Dual IP Settings are valid only when used with Conettix IP communication format. IP module 1
is ITS-DX4020-G module or B426 module; IP module 2 is B426 module. IP module 2 does not
support RPC connection.
When the report is transmitted with Conettix IP Communication, some reports might be
missed. It is recommended not to separately use the ITS-DX4020-G module. If the ITS-DX4020-
G module is used, other network modules (e.g. B426) or the public telephone network can be
set as backup channel to ensure that no reports are missed.
The communication path of B426 / ITS-DX4020-G is as follows:
Module Address Setting Corresponding
Communication Path
Module 1: B426 module 1 / ITS-
DX4020-G
134 Paths 1 and 2
Module 2: B426 module 2 250 Paths 3 and 4
Only when IP module 1 is used and set to paths 1 to 4, the report can be sent to those paths.
Remote Access
The AMAX panel supports remote programming via USB, telephone or IP network using
software A -Link Plus.
uploading / downloading programming parameters
7.1.3
7.1.4
7.1.5
40 en | Settings AMAX 2100 / 3000 / 4000
2013.10 | 01 | F.01U.267.112 Installation Guide Bosch Sicherheitsysteme GmbH
40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch AMAX 4000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Bosch AMAX 4000

Bosch AMAX 4000 Installationsanweisung - Deutsch - 170 seiten

Bosch AMAX 4000 Kurzanleitung - Deutsch - 34 seiten

Bosch AMAX 4000 Bedienungsanleitung - Englisch - 24 seiten

Bosch AMAX 4000 Bedienungsanleitung - Englisch - 36 seiten

Bosch AMAX 4000 Kurzanleitung - Englisch - 38 seiten

Bosch AMAX 4000 Installationsanweisung - Holländisch - 166 seiten

Bosch AMAX 4000 Bedienungsanleitung - Holländisch - 24 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info