Bedienungsanleitung Bosch AMAX panel 4000 EN (Seite 48 von 170) (Englisch)

697454

Zoom out

Zoom in

Vorherige Seite

1/170

Nächste Seite

48 en | Settings AMAX panel

2019.08 | 11 | F.01U.309.277 Installation Manual Bosch Security Systems B.V.

RPC gets the Subscriber ID, IP address and port from the UDP data packets (IP No. and Port

is parsed from UDP data packet).

RPC with running RPS (Remote Programming Software = A-Link Plus) saves the received UDP

data packet information into its own RAM, the information is lost after RPS is closed.

When a connection is started and the IP address set in the customer information doesn’t

match with the IP Address from the RAM, the A-Link Plus opens a window to ask if the new IP

Address and Port should be used.

When RPS is opened, a connection can only be established when the IP address and port

number of the AMAX panel have not changed, after RPS received previous data.

If the IP address has changed RPC with running RPS must wait for the next UDP Data package

send from the Panel. When the connection is established, the AMAX panel sends a polling

telegram of 25 bytes.

6.1.8 Call back and domestic call

Call back telephone number

This address stores the telephone number to call when upload / download is requested or the

user enters his code + [5] [7] and presses [#] to initiate a modem call from the AMAX panel to

establish a communication link with the remote computer. The computer must be running

remote programming software A-Link Plus and must be set to waiting for an incoming call. The

call back telephone number is also necessary if remote connect with call back verification is

required.

Domestic call

Four recordable voice messages for four dialing telephone numbers are supported. Each of the

four recordable voice messages can take up to 9 seconds. The voice messages are recorded

with the tool “Rec.exe” that comes with A-Link Plus and are transferred via A-Link Plus to the

AMAX panel. They can only be transferred via USB or network connection. The supported

format of the voice message files is the following:

– For firmware version up to 1.4: .wav

– For firmware version 1.5 and higher: .va3

When the AMAX panel is activated into zone tamper / zone alarm, the programmed telephone

number is dialed and the recorded voice message is played.

All alarm events only need one report / acknowledgement.

The transmission sequence is repeated until the AMAX panel receives an acknowledgement

tone.

The AMAX panel automatically hangs up after about 45 seconds if it cannot detect the

acknowledgement tone and redial later.

The user presses any key on the telephone between two acknowledgement tones to confirm

the alarming.

The acknowledgement tone is the DTMF signal sent by the remote user with any key ([0] - [9]

or [*] or [#]).

If the AMAX panel received the acknowledgement from the user, it will send a 2 seconds long

confirmation beep as an acknowledge tone and hang up the line.

6.1.9 Ring times

Ring Count

This function defines the number of rings before the AMAX panel answers an incoming call. It

is necessary to enable remote arming and remote upload/download to use this function.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch AMAX panel 4000 EN Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch AMAX panel 4000 EN

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info