Bedienungsanleitung Bosch AXT 22 D (Seite 16 von 258) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

591611

Zoom out

Zoom in

Vorherige Seite

1/258

Nächste Seite

16 | English

F 016 L81 145 | (28.8.14) Bosch Power Tools

used. The operator is responsible for

third persons in the working area.

Bosch can assure flawless function-

ing of the machine only when original

accessories are used.

Become familiar with the instruction

manual before attempting to operate

this machine.

Avoid wearing loose-fitting clothing,

hanging cords or ties.

Only operate the machine in open

space (e. g. not too close to a wall or

other fixed objects) and on a firm,

level surface.

Do not operate the machine on paved

or gravel surface where ejected mate-

rial could cause injury.

Before starting the machine, check

that all screws, nuts, bolts and other

fasteners are properly secured and

that guards and screens are in place.

Replace damaged or unreadable

warning and operating labels.

Before starting the machine, make

certain that the chute assembly is

empty.

Keep your face and body away from

the chute assembly.

Do not allow hands or any other part

of the body or clothing inside the

chute assembly, discharge chute or

near any moving part.

Keep proper balance and footing at

all times. Do not overreach. Never

stand at a higher level than the base

of the machine when feeding materi-

al.

Always stand clear of the discharge

zone when operating the machine.

When feeding material into the ma-

chine be extremely careful that piec-

es of metal, rocks, bottles, cans or

other foreign objects are not includ-

ed.

If the cutting mechanism strikes any

foreign object or if the machine

should start making any unusual

noise or vibration, immediately

switch off and allow the cutter to

stop. Remove the plug from the

mains supply and take the following

steps:

– Inspect for damage.

– Replace or repair any damaged parts.

– Check for and tighten any loose parts.

Do not attempt to repair the machine

unless you are qualified to do so.

Do not allow processed material to

build up in the discharge zone; this

may prevent proper discharge which

can result in kickback of material

through the chute assembly.

If the machine becomes clogged,

switch off and allow the cutter to

stop. Remove the plug from the

mains supply before clearing debris.

Check if guards and protective devic-

es are undamaged and properly

mounted. Before using, carry out any

necessary maintenance and repairs.

Do not tamper with the motor speed

control settings. Contact a Bosch ap-

proved service agent if a problem ex-

ists.

Keep the motor cooling vents clean of

debris and other accumulations to

prevent damage to the motor or pos-

sible fire.

OBJ_BUCH-895-004.book Page 16 Thursday, August 28, 2014 9:05 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch AXT 22 D Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info