Bedienungsanleitung Bosch D-tect 150 (Seite 21 von 345) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544331

Zoom out

Zoom in

Vorherige Seite

1/345

Nächste Seite

English | 21

Bosch Power Tools 1 609 929 X40 | (30.8.10)

Method of Operation (see figure B)

The measuring tool

checks the base mate-

rial of sensor area 9 in

measurement direction

A to the displayed

measuring depth. Meas-

urement is possible

only during movement

of the measuring tool in

the direction of travel B

and for a measuring dis-

tance of at least 10 cm.

Move the measuring

tool in a straight line with light pressure over

the wall so that the wheels remain in contact

with the wall. Objects are detected that differ

from the material of the wall. The allowable

drilling depth and, if possible, the object mate-

rial, are indicated on the display.

Optimum results are achieved when the meas-

ured distance is at least 40 cm and the measur-

ing tool is moved slowly over the entire location

to be checked. The tool’s method of operation

ensures reliable detection of outer object edges

that run transverse to the measuring tool’s

movement direction.

Therefore, always move crossways over the

area to be checked.

If several objects are located one over the other

in the wall, the object that is indicated in the dis-

play is the one nearest to the surface.

The representation of the properties of detect-

ed objects in the display 16 can deviate from the

actual object properties. This applies particular-

ly for very thin objects, which are represented

thicker in the display. Large cylindrical objects

(e.g. plastic or water pipes) can appear in the

display smaller than they actually are.

Detectable Objects

– Plastic pipes (e.g. water-carrying plastic

pipes, as used in floor/wall-heating systems,

with at least 10 mm in diameter; empty pipes

with at least 20 mm in diameter)

– Electrical wiring (independent of whether

carrying voltage or not)

– Three-phase mains wiring (e.g. to the stove)

– Low-voltage wiring (e.g. for door bell, tele-

phone

– Metal pipes, bars, beams of any type (e.g.

steel, copper, aluminium)

– Reinforcing steel

– Wooden beams

– Hollow spaces

Measurements possible

– In brickwork (bricks, porous concrete, foam

concrete, aerated concrete, lime-sand brick)

– In concrete/reinforced concrete

– In light construction walls

– Under surfaces such as stucco, tiles, wall-

paper, parquet flooring, carpet

– Behind wood, gypsum board

Special Measuring Cases

Based on the measuring priniciple, unfavourable

conditions can influence the measuring result,

for example:

– Multi-layered walls

– Empty plastic pipes and wood beams in hol-

low spaces and light construction walls

– Objects running inclined in walls

– Metal surfaces and damp areas; in walls,

these can possibly be indicated as an object

(e.g. when the water content is high).

Please observe that concrete requires sever-

al months to dry completely.

– Hollow spaces in a wall; these can be indicat-

ed as objects.

– Closeness to equipment that generates

strong magnetic or electromagnetic fields,

e.g. radio base stations or generators.

SENSO

OBJ_BUCH-844-006.book Page 21 Monday, August 30, 2010 10:44 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch D-tect 150 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info