Bedienungsanleitung Bosch D-tect 150 (Seite 22 von 345) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544331

Zoom out

Zoom in

Vorherige Seite

1/345

Nächste Seite

22 | English

1 609 929 X40 | (30.8.10) Bosch Power Tools

Initial Operation

f Protect the measuring tool against mois-

ture and direct sun light.

Switching On and Off

f Before switching the measuring tool on,

make sure that the sensor area 9 is not

moist. If required, dry the measuring tool us-

ing a soft cloth.

f If the measuring tool was subject to an ex-

treme temperature change, allow it to ad-

just to the ambient temperature before

switching on.

Switching On

–To switch on the measuring tool, press the

On/Off button 15 or the start button 11.

–LED 17 lights up green and the start display

is indicated for 4 s on display 16.

– When no measurement is carried out and no

button is pressed for 5 minutes, the measur-

ing tool switches off automatically. This

“Cut-off time” can be changed in the “Set-

tings” menu (see “Cut-off Time”, page 25).

Switching Off

–To switch the measuring tool off, press the

On/Off button 15.

– When switching off the measuring tool, all

settings are retained in the menus.

Switching the Audio Signal On/Off

The audio signal can be switched on/off with the

audio signal button 13. This “Tone signal” can

be changed in the “Settings” submenu (see

“Tone Signals”, page 25).

Measuring Procedure

Switch the measuring tool on. The “standard

start display” appears on display 16.

Position the measuring tool against the wall and

move it over the wall in the direction of travel

(see “Method of Operation”, page 21). Meas-

ured results are indicated on display 16 after a

minimum measuring distance of 10 cm. To en-

sure correct measurement results, move the

measuring tool slowly and completely over the

assumed object in the wall.

If the measuring tool is lifted away from the wall

during a measurement, the last measured result

remains on the display. “Hold” appears on the

sensor-range indicator c. When the measuring

tool is placed against the wall again, moved on

or when the start button 11 is pressed, the

measurement starts anew.

When LED 17 lights up red, an object is in the

sensor range. When LED 17 lights up green, no

object is in the sensor range. When LED 17

flashes, a “live” object is in the sensor range.

f Before drilling, sawing or routing into a

wall, protect yourself against hazards by us-

ing other information sources. As the meas-

uring results can be influenced through ambi-

ent conditions or the wall material, there may

be a hazard even though the indicator does

not indicate an object in the sensor range

(LED 17 lit green).

0 cm

Sensor

Universal mode

Prev Next

Move

OBJ_BUCH-844-006.book Page 22 Monday, August 30, 2010 10:44 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch D-tect 150 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info