Bedienungsanleitung Bosch EasyCut Grind (Seite 21 von 247) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

766864

Zoom out

Zoom in

Vorherige Seite

1/247

Nächste Seite

English | 21

antly increase the exposure to vibration over the total work-

ing period.

To estimate the exposure to vibration accurately, the times

when the tool is switched off or when it is running but not ac-

tually being used should also be taken into account. This can

significantly reduce the exposure to vibration over the total

working period.

Implement additional safety measures to protect the oper-

ator from the effects of vibration, such as servicing the

power tool and application tools, keeping the hands warm,

and organising workflows correctly.

Fitting

Battery Charging (seefigureA)

uUse only the power adaptors listed in the technical

data. Only these power adaptors are matched to the lith-

ium-ion battery of your power tool.

Note: The battery is supplied partially charged. To ensure

the maximum performance of the battery, use the power ad-

aptor to fully charge the battery before first use.

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by the "Electronic Cell Protection (ECP)". When the battery

is discharged, the power tool is switched off by means of a

protective circuit: The application tool stops moving.

uDo not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

To charge the battery, connect the USBType-C™ port(2) to

the power adaptor(9) via the USB cable(10). Plug the

power adaptor into a plug socket. The charging process will

begin.

The battery charge indicator(3) indicates the charging pro-

gress. During the charging process, the power tool is deac-

tivated and cannot be used.

If you are not planning to use the power tool again soon, dis-

connect the power adaptor(9) from the mains.

Battery charge indicator

The battery charge indicator(3) displays the battery's state

of charge for a few seconds when switching on the power

tool. When charging, the battery charge indicator goes out a

few minutes after the battery has been fully charged.

Capacity LED when switched

on LED when charging

100% Green (continuous) Green (continuous)

100%−

50% Green (continuous) Green (flashing)

50%−

20% Yellow (continuous) Green (flashing)

20%−5% Red (continuous) Green (flashing)

5%−0% Red (flashing) Green (flashing)

Note: If the battery charge indicator is flashing white, the

temperature is outside the permitted temperature range.

Once the permitted temperature range has been reached

again, the charging process automatically resumes or the

power tool can be used once again.

Adjusting the Hood (seefigureB)

Note: If the grinding disc breaks during operation or the

holding fixtures on the hood/power tool become damaged,

the power tool must be sent to the after-sales service imme-

diately; see the "After-Sales Service and Application Service"

section for addresses.

Turn the hood to the required position and ensure that the

hood is engaged. No tool is required for this.

Fitting the abrasive tools

uDo not touch grinding and cutting discs until they have

cooled down. The discs can become very hot while work-

ing.

uOnly change the abrasive tool when the power tool is

locked (see "Switching on/off", page22).

Clean the grinding spindle(12) and all parts to be mounted.

To tighten or loosen the abrasive tools, press the spindle

lock button(6) and simultaneously turn the grinding tool to

fix the grinding spindle in place.

uDo not press the spindle lock button while the grind-

ing spindle is moving. The power tool may become dam-

aged if you do this.

Sanding plate/cutting disc

Pay attention to the dimensions of the abrasive tools. The

diameter of the hole must match that of the mounting flange.

Do not use an adapter or reducer.

To remove the grinding/cutting disc(8), press the spindle

lock button(6) while simultaneously turning on the grinding/

cutting disc(8) in order to fix the grinding spindle(12) in

place. Use the hex key of the transportation cover(13) to re-

move the clamping bolt with washer(15). Take off the grind-

ing/cutting disc(8). (SeefigureC).

To secure the grinding/cutting disc(8), press the spindle

lock button(6). Screw in the clamping bolt with

washer(15). Tighten the clamping bolt using the hex key of

the transportation cover(13) until the washer of the clamp-

ing bolt is flush with the grinding/cutting disc(8).

(SeefigureD).

uAfter fitting the abrasive tool, check that the abrasive

tool is fitted correctly and can turn freely before

switching on the power tool. Make sure that the abras-

ive tool does not brush against the protective guard or

other parts.

Approved abrasive tools

You can use all the abrasive tools mentioned in these operat-

ing instructions.

The permissible speed [min-1] or the circumferential speed

[m/s] of the abrasive tools used must at least match the val-

ues given in the table.

Bosch Power Tools 1 609 92A 6EL | (04.02.2021)

Bosch EasyCut Grind Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info