Bedienungsanleitung Bosch EasyCut Grind (Seite 22 von 247) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

766864

Zoom out

Zoom in

Vorherige Seite

1/247

Nächste Seite

22 | English

It is therefore important to observe the permissible rota-

tional/circumferential speed on the label of the abrasive

tool.

max.

[mm] [mm]

D d [min-1] [m/s]

50 10 30,600 80

Selecting the Grinding/Cutting Disc

Grinding tool Material

Carbide Multi Ma-

terial Disc Wood (with nails),

plastic, PVC, com-

posite materials,

acrylic glass

Bonded Metal Cut-

ting Disc Metal, aluminium,

copper

Sanding plate with

abrasives Wood, metal

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some

wood types, minerals and metal can be harmful to one’s

health. Touching or breathing-in the dust can cause allergic

reactions and/or lead to respiratory infections of the user or

bystanders.

Certain dust, such as oak or beech dust, is considered carci-

nogenic, especially in connection with wood-treatment ad-

ditives (chromate, wood preservative). Materials containing

asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the ma-

terials to be worked.

uAvoid dust accumulation at the workplace. Dust can

easily ignite.

Operation

Start-up

Switching on/off

To unlock the power tool, press the lock-off button(4). The

status LED(1) lights up green. Then press the on/off

switch(5) and keep it pressed down to switch on the power

tool. While the status LED(1) is lit green, the power tool is

unlocked.

To switch off the power tool, release the on/off switch(5).

Then press the lock-off button(4) to lock the power tool. If

the power tool has not been switched on for longer than five

minutes, it will be locked automatically.

If the power tool does not switch off after releasing the on/

off switch(5), press the lock-off button(4).

uAlways check abrasive tools before using them. The

abrasive tool must be fitted properly and be able to

move freely. Carry out a test run for at least one

minute with no load. Do not use abrasive tools that are

damaged, run untrue or vibrate during use. Damaged

abrasive tools can burst apart and cause injuries.

Working Advice

uClamp the workpiece if it is not secure under its own

weight.

uDo not load the power tool so heavily that it comes to a

stop.

uIf the power tool has been subjected to a heavy load,

continue to run it at no-load for several minutes to

cool down the accessory.

uDo not use the power tool with a cut-off stand.

uWhen cutting lightweight materials, take into account

the statutory provisions and recommendations of the

material manufacturer.

uDo not touch grinding and cutting discs until they have

cooled down. The discs can become very hot while work-

ing.

Cutting metal

When carrying out abrasive cutting, use a moderate feed

that is suited to the material being machined. Do not exert

pressure on the cutting disc and do not tilt or swing the

power tool.

Do not attempt to reduce the speed of a cutting disc coming

to a stop by applying pressure from the side.

The power tool must always work in an up-grinding motion.

Otherwise there is a risk that it will be pushed uncontrolled

out of the cut.

For best results when cutting profiles and rectangular

tubing, start at the smallest cross section.

Information on structural design

Slots in load-bearing walls are subject to DIN 1053 part 1 or

country-specific regulations. These regulations must be ob-

served under all circumstances. Seek advice from the re-

sponsible structural engineer, architect or construction su-

pervisor before starting work.

Cutting aid (seefigureE)

The cutting aid(14) allows you to make a precise cut when

separating materials. Ensure that the cutting aid (14) is

firmly engaged before making the cut. To do this, turn the

cutting aid(14) together with the hood(7) so that the snap-

in fin(17) engages in the recess(16).

Transportation cover (seefigureF)

Fit the transportation cover(13) to transport the power

tool. This serves to prevent injuries and damage.

1 609 92A 6EL | (04.02.2021) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch EasyCut Grind Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info