Bedienungsanleitung Bosch EasyHammer 12V (Seite 15 von 93) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch)

766855

Zoom out

Zoom in

Vorherige Seite

1/93

Nächste Seite

English | 15

Note: The battery is supplied partially charged. To ensure

the maximum performance of the battery, use the power ad-

aptor to fully charge the battery before first use.

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by the "Electronic Cell Protection (ECP)". When the battery

is discharged, the power tool is switched off by means of a

protective circuit: The application tool stops moving.

uDo not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

– Open the flap(9).

– Connect the USB port(8) to the power supply(17).

– Plug the power supply(17) into the plug socket.

The charging process will begin. The battery charge

indicator(7) indicates the charging progress.

During the charging process, the power tool is deactivated

and cannot be used.

If you are not planning to use the power tool again soon, dis-

connect the power adaptor(17) from the mains.

Battery charge indicator

The battery charge indicator (7) indicates the state of

charge for a few seconds when the on/off switch (5) is half

or fully pressed.

After charging, the battery charge indicator (7) goes out a

few minutes after the battery has been fully charged.

Capacity LED when switched

on LED when charging

100% Green (continuous) Green (continuous)

100%−

50% Green (continuous) Green (flashing)

50%−

20% Yellow (continuous) Green (flashing)

20%−5% Red (continuous) Green (flashing)

5%−0% Red (flashing) Green (flashing)

Note: If the battery charge indicator is flashing white, the

temperature is outside the permitted temperature range.

Once the permitted temperature range has been reached

again, the charging process automatically resumes or the

power tool can be used once again.

Selecting Tools

An application tool with hexagonal shank with groove or SDS

quick shank is required for drilling and hammer drilling.

For screwdriving, only use screwdriver bits that have a

hexagonal shank with groove (14). Other short screwdriver

bits (16) can be inserted using a universal bit holder with

hexagonal shank with groove (15).

You will find a selection of suitable application tools in the

accessories overview at the end of these operating instruc-

tions.

Changing the Tool

The tool holder can also accommodate dif-

ferent application tools with a hexagonal

shank with groove and SDS quick shank.

The tool holder allows for simple and con-

venient tool-free changing of the application

tool.

As a requirement of the system, the application tool can

move freely. This causes a certain radial run-out at no-load,

which has no effect on the accuracy of the drill hole, as the

drill bit centres itself upon drilling.

The dust protection cap (2) largely prevents the penetration

of drilling dust into the tool holder during operation. When

inserting the tool, make sure that the dust protection cap (2)

does not become damaged.

uReplace a damaged dust protection cap immediately.

It is recommended that you have use an after-sales

service for this.

Inserting the application tool (see figure B)

– Clean the shank of the application tool.

– Using a gradual turning motion, push the application tool

into the tool holder until it locks itself in place.

– Check it is locked by pulling the tool.

Removing the application tool (seefigureC)

– Push the locking sleeve (3) back and remove the applica-

tion tool.

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some

wood types, minerals and metal can be harmful to one’s

health. Touching or breathing-in the dust can cause allergic

reactions and/or lead to respiratory infections of the user or

bystanders.

Certain dust, such as oak or beech dust, is considered carci-

nogenic, especially in connection with wood-treatment ad-

ditives (chromate, wood preservative). Materials containing

asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the ma-

terials to be worked.

uAvoid dust accumulation at the workplace. Dust can

easily ignite.

Operation

Start-up

uEnsure that the flap of the USB Type-C® port(9) is closed

during operation. This will prevent dust from getting in.

Bosch Power Tools 1 609 92A 4MK | (28.01.2021)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch EasyHammer 12V Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info