Bedienungsanleitung Bosch GAS 18V-10 L (Seite 18 von 221) (Alle Sprachen)

786180

Zoom out

Zoom in

Vorherige Seite

1/221

Nächste Seite

18 | English

Changing the Battery Compartment Cover

(seefiguresA3−A5)

If you wish to use a ProCORE18V 12Ah battery, the battery

compartment cover(12) can then no longer be closed. In

this case, the battery compartment cover(12) can be re-

placed with a screen(23) designed for this purpose.

In damp or wet conditions, the dust extractor may only be

used with the battery compartment cover closed.

Removing the Battery Compartment Cover

(seefigureA3)

Remove the battery(20) from the battery bay(19).

Remove the two fastening screws(22) (ST4×12) with a

cross-headed screwdriver PH1 and take off the battery com-

partment cover(12).

Inserting the Screen (seefigureA4)

Press the battery compartment cover bracket(24) down-

wards and slide on the screen(23).

Removing the Screen (seefigureA5)

Apply a slot screwdriver, push the screen(23) a little way to-

wards the rear and remove the screen. When doing so, press

the battery compartment cover bracket(24) downwards.

Fitting the Brackets for Extractor Accessories

(seefigureB)

– Slide the bracket(25) for the suction tube and crevice

nozzle firmly into the adapter(10) provided for it from

above until it clicks into place.

– Slide the bracket(27) for the vacuum hose and floor

nozzle firmly into the adapter(7) provided for it from

above and tighten the fixing bolts(26).

Fitting the vacuum hose (see figure C)

– Insert the vacuum hose (13) into the hose adapter (8) un-

til both snap fasteners (28) of the vacuum hose click into

place.

Note: The friction generated by the dust in the vacuum hose

and accessory during extraction causes an electrostatic

charge that the user may experience as static discharge (de-

pending on environmental factors and their physiological

state).

Fitting the Vacuuming Accessories

The vacuum hose(13) is equipped with a clip system which

can be used to connect vacuuming accessories (dust extrac-

tion adapter(14), curved nozzle(15)).

Fitting the extraction adapter or curved nozzle

(seefigureD)

– Fit the extraction adapter(14) or the curved nozzle(15)

to the vacuum hose(13) until the two snap

fasteners(28) on the vacuum hose audibly click into

place.

– To remove the adapter, press the snap fasteners(28) in-

wards and pull apart the components.

Fitting the Nozzles and Tubes

– If required, place the suction tubes (18) firmly inside one

another and then attach them firmly to the curved nozzle

(15).

– Attach the floor nozzle (17) or the crevice nozzle (16)

firmly to the suction tube (18) or the curved nozzle (15).

Attaching the carrying strap (seefigureE)

uThe carrying strap is only intended for carrying and at-

taching the dust extractor and not as a safety harness.

Click the snap hooks of the carrying strap(29) into the

fastening eyes(9) of the dust extractor.

Fitting the Rollers (seefigureF)

Insert the 4 fastening pins on the rollers(30) into the roller

adapters(31) until they audibly click into place.

Other rollers can also be used as per the EN12529 standard

(11mm fastening pin diameter).

uCheck the functionality of the roller brakes before us-

ing the dust extractor.

Operation

uRemove the battery before cleaning or performing

maintenance on the dust extractor, making tool ad-

justments, changing accessories or placing the dust

extractor in storage. This safety measure prevents the

dust extractor from being started accidentally.

uEnsure that the work area is clean and tidy to minim-

ise the risk of tripping.

Starting Operation

uThe dust extractor must not be used without a filter.

uDo not use damaged filters (e.g. no cracks, small

holes, etc.). Replace any damaged filters immedi-

ately.

uBefore extraction, ensure that the filter unit is se-

curely fitted.

uBefore extraction, ensure that the battery compart-

ment cover is securely closed.

uPlease inform yourself about the applicable regula-

tions/laws on how to handle harmful types of dust in

your country.

uOnly vacuum rock dust with the power tool and dust

extraction system combination explicitly identified,

for which it has been proven that the legal thresholds

are not exceeded. You can find this evidence at

http://www.bosch-professional.com/dust.

The dust extractor must categorically not be used in poten-

tially explosive areas.

To ensure optimum suction power, you must always fully un-

wind the vacuum hose(13) from the vacuum hose

bracket(27).

1 609 92A 7MV | (12.05.2022) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GAS 18V-10 L Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info